Wimberley TX Heating & Air Conditioning Services

Performed A/C tune-up on a American Standard heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Cleaned the exterior of the air handler and washed the outdoor coil. No major issues were found. The system is operational at this time.

AC cool check completed on two year-old horizontal heat pump system. Drain line cleared and condenser coil cleaned. No major issues were found. The system is cooling properly at time of departure.

Performed heater tune-up on two Carrier straight cool systems. Checked the electrical, mechanical and performance systems of the units. Replaced the return air filters. Cleared, cleaned, flushed and treated the drain lines. Cleaned the exterior of the furnace systems and washed both outdoor coils. I replaced the high voltage wire nuts with a Wago wire connector on both furnace systems. I also adjusted the airflow on the upstairs 3-ton system to deliver 1100 cfm. No other issues were found. Both systems are operational at this time.

Performed A/C tune-up on a Carrier heat pump system and checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Cleaned the exterior of the furnace and replaced the return air filter. Verified the compressor wiring is secure and washed the outdoor coil. No major issues were found. The system is operational at this time.

Performed A/C tune-up on a Carrier heat pump system and checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. Verified the compressor wiring is secure and washed the outdoor coil. No major issues were found. The system is operational at this time.

Performed A/C tune-up on a Carrier heat pump and one mini split system. I checked the electrical, mechanical and performance systems of the units. Cleared, cleaned, flushed and treated the drain lines. Cleaned the exterior of the indoor system and washed both outdoor coils. No major issues were found. Both systems are operational at this time.

Performed heater A/C tune up on a Carrier heat pump system and checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Washed the outdoor coil and secured the compressor wiring. I found the return side has high static at .46 in.W.C. No other issues were found. All UV light and surge protection devices are working. The system is operational at this time.

Performed AC cool check on three systems and checked the electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain lines and flow tested the drains with two gallons of water. I also treated the drain lines. The air filters were replaced with client supplied filters. Condenser coils cleaned. No major issues were found. The systems were running at the completion of service.

Replaced all registers and Iboxes. Sealed all Iboxes to the Sheetrock. Installed new metal supply and return plenums. Ran new flex to Iboxes. Installed 2 sheet metal wyes going back to the living room. Installed new return air grille and sealed. Cleaned the blower wheel housing and blower motor. Cleaned the unit. Cleared the drain and verified operation.

Upsized the 3 ducts going to the living room. Changed the registers in the living room, kitchen and guest bedroom. Extended return duct in satellite return to main return plenum. Sealed all connections with mastic air lock. Hung flex duct for proper air flow. Everything is operational at this time.

Heater check performed on two horizontal heat pump systems. All mechanical and electrical are within manufacture specs. No major issues were found at this time. Both systems are heating properly at time of departure.

Performed heater check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. No other major issues were found. The system was running at the completion of service.

Installed new extended supply plenum. Installed new return plenum and plenum transition. Installed a new supply and a new return bucket in the master bedroom. Upsized both living room supply ducts. Sealed all connections with mastic airlock.

Performed heater check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The homeowner did not have a replacement filter at this time. No major issues were found. The system was running at the completion of service.

Built a new extended supply and a new return plenum. Sealed all connections with mastic. Attached all duct work with new metal collars. Completed duct sealing around all I-boxes. Pulled and cleaned the blower assembly. Completed a duct cleaning of all flex runs. Everything is operational at this time.

Performed heater check on two systems. Filters were replaced with customer supplied filters. I cleared both condensation drains, and flow tested them with two gallons of water. I also treated the drain lines. The main house has a dirty blower wheel. The condenser fan motor is showing signs of overheating and the contractor is burnt. Options for repair were presented to the homeowners. Both systems were running at the completion of service.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a customer supplied filter. No major issues were found. The system was running at the time of departure.

Performed the heater tune-up on a Trane heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. I replaced the filter with a customer supplied filter. Washed the outdoor coil and verified the compressor wiring is secure. I checked refrigerant levels in cooling mode since the outdoor temperature is at 65 degrees and found that they are within range. I did find that the outdoor condenser fan motor has a hot spot. No other major issues were found, and the system is operational at this time.

Performed heat check on two systems. Checked electrical, mechanical, safety, and performance of the systems. I cleared the drain lines and flow tested the drains with water. I also treated the drain lines. Both Reme-Halo air purifiers have failed. Both blower wheels are developing mold growth. There are mold/mildew spots inside the air handlers as well. I spoke to homeowner and the current state of the systems and their age. Both systems were running at the completion of service.

Performed heat check. Checked electrical, mechanical, safety, and performance the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. System sterilizers are operational. The air filter was replaced with a customer supplied filter. No major issues found. The system was running at the completion of service.