HVAC Service In Buda, TX

Installed Payne furnace and condenser. Installed Ecobee lite thermostat. Built extended supply plenum. Built return plenum and installed media filter. Sealed all connections with mastic and mesh tape. Rebuilt and insulated primary drain line. Cleared drain and verified operation. Replaced secondary drain pan. Replaced gas flex and rebuilt flu pipe. Replaced disconnect and whip at outdoor condensing unit. Ran low voltage in 1/2 inch seal-tite. Weighed in additional charge to meet manufacturer specifications. Everything is working at completion of service.

Performed diagnostic on the system and found that the primary drain line was clogged and buried underground. This tripped the water safety switch and shutoff the system. I spoke with the homeowner and she chose to have the drain serviced. I cleared and treated the drain line and verified it is draining properly. I also put new insulation on the suction line, secured the compressor wiring and washed the outdoor coil at no additional cost. The system is operational at this time.

Started by pumping down the system Removed the case coil and installed new case coil and filter drier. Pressure tested line set and pulled a vacuum. Transitioned supply plenum and sealed all connections with mastic and mesh tape. Rebuilt primary and secondary drain, cleared the drain after to make sure it was operating as it should. Set line set information at thermostat and charged accordingly. Cycled the system, everything is operational at completion of service.

Performed A/C tune-up on a Carrier straight cooling system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I replaced the air filter with a client supplied filter. Secured the compressor wiring and washed the outdoor coil. No issues were found. The system is operational at this time.

Performed semiannual maintenance on one heat pump cooling system. Inspected all performance, mechanical and safety systems. Changed out two air filters that the homeowner provided to us and sealed them inside the return air filter grille. Verified everything was operating within manufacturer specifications for operation. Ensured the surge protection devices and air purifier are on and operating during todays visit. No major issues were found. Everything is working at this time.

AC cool check completed for two systems. Both drain lines were cleared, treated, and primed. Both condenser coils were cleaned. I found the thermostat wire running to one of the condensers to have extreme wear and tear, showing exposed wiring. I went over my findings with the homeowner and she chose to fix the wire running to the condenser. I completed the repair and function tested the system. No other major issues were found. Both units are cooling properly at this time.

Service diagnostic found that the condensation drain line was clogged. Water had backed up into the safety switch and shut down the system. Options for repair were presented to the customer and he decided to have the drain line cleared and to sign up for maintenance. I cleared the condensation drain line and flow tested the drain with two gallons of water. Clear water was observed flowing freely out of the drain line. I also treated the drain line. I function tested the system and the system was running normally. Everything was running at the completion of service.

Recovered existing refrigerant charge. Installed new compressor with new wiring harness. Installed ICM voltage monitor. Pressure tested system with nitrogen and pulled vacuum. Replaced secondary drain pan. Rebuilt primary and secondary drains and added SS2 / SS3 safety switches. Cleared drain on both systems. Charged AC with R-410A to 10 subcooling. Tested operation of both upstairs and downstairs system. Everything is working at completion of service.

Performed semiannual maintenance on one straight cool AC system. Inspected all performance, mechanical and safety systems. Tested and verified everything was operating within manufacturer specifications for operation. Everything is working at this time.

Performed semiannual maintenance on one heat pump cooling system. Inspected all performance, mechanical and safety systems. I found that the indoor evaporator coil is extremely rusted and corroded. Will want to monitor refrigerant levels to see if any refrigerant leaks appear. During today’s visit, refrigerant levels were operating at a 9°SC/9°SH which is running within manufacturer specifications for operation. Flushed and cleared the primary condensate drain line to ensure proper drainage of condensate. Tested and verified everything was operating within manufacturer specifications for operation. No other major issues were found. Everything is working at this time.

On arrival I found the low voltage fuse blown. I used my resettable fuse and powered the system up. Cycled power a few times and inspected the wiring. I ran the system for a while with no issues. My amp draw on the low voltage stayed at a constant .31 amps. I spoke with homeowner, and he chose to have a maintenance done on the system at this time. I cleared, flushed, and treated the drain line. Washed the outdoor coil and secured the compressor wiring. I did find the outdoor capacitor (30/7.5) is reading below the rated value. No other major issues were found. System is operational at this time.

Performed an A/C tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Verified the compressor wiring is secure and washed the outdoor coil. No major issues were found, and the system is operational at this time.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. Condenser coil was cleaned. No major issues were found. The system was running at the completion of service.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. Air filter was replaced with a client supplied filter. Condenser coil was cleaned. I did see that the condenser unit had a surge protector installed at the disconnect, however there was no surge protector installed for the furnace. Options for installing a surge protector on the furnace were presented to the customer. He chose to have the surge protector installed at today's visit. I installed the surge protector on the furnace and function tested the system. No major issues were found. The system was running at the completion of service.

Performed semiannual maintenance on one heat pump cooling system. Inspected all performance, mechanical and safety systems. Tested and verified everything was operating within manufacturer specifications for operation. Changed out one AprilAire 313 air filter supplied by the homeowners. No major issues were found. Everything is working at this time.

Installed 2 Ton R-454B Carrier 2 stage heat pump condenser and air handler with heat kit. Installed Ecobee pro thermostat. Placed condenser on new leveled pad. Built and installed new supply and return plenums. Sealed all connections with mastic / hardcast. Installed new secondary drain pan. Rebuilt primary condensation drain line and installed SS2 / SS3 safety switches. Cleared drain with CO2 and primed trap with water. Pressure tested system with nitrogen and pulled vacuum. Charged AC with R-454B refrigerant. Tested heating and cooling operation. Everything is working at completion of service.

Performed semiannual maintenance on one heat pump cooling system. Inspected all performance, mechanical and safety systems. Tested and verified everything was operating within manufacturer specifications for operation. No major issues were found. Everything is working at this time.

Performed semiannual maintenance on one heat pump heating system. Inspected all performance, mechanical and safety systems. Flushed and treated the primary drain line and cleaned out the return air chase of all the dirt and dust. Verified everything was operating within manufacturer specifications for operation. System had a 20° temperature split between return and supply. Everything is working at this time.

AC cool check completed on horizontal carrier system. I cleared and treated the condensate drain line. Condenser coil was cleaned. There was no surge protection on the AC system. I spoke to the homeowner about options to add surge protection and they chose to install surge protection on both the furnace and condenser. I installed the surge protectors and function tested the system. No major issues were found. The system is cooling properly at time of departure.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. Air filters were replaced with client supplied filters. Condenser coil was cleaned. The surge protector for the air handler was operational, however they did not have a surge protector installed for the condenser unit. Options for repair were presented to the homeowners and they decided to have a surge protector for the condenser unit installed. I installed a surge protector for the condenser unit and function tested the system. No major issues were found. The system was running at the completion of service.