HVAC Service In Buda, TX

Performed service diagnostic. The diagnostic found that the capacitor on the condenser unit has failed. The air handler and evaporator coil have some mold/mildew inside as well. Options for repair were presented to the customers. They chose to have the capacitor replaced on the condenser unit. Repair completed. The system was function checked and was running at the time of departure.

Performed semiannual maintenance on one heat pump cooling system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time.

Installed new Eco bee pro thermostat. Rebuilt and insulated condensate drain line. Added SS2 and SS3 safety float switch. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Replaced the disconnect and ran the low voltage in seal tight. Replaced both supply and return plenums and sealed with a mastic airlock. Charged system to factory spec and performed a benchmark. System is working properly at time of departure.

Performed semiannual maintenance on one straight AC cooling unit. Inspected all Performance, Mechanical and Safety Systems. When doing maintenance on the outdoor unit I found that the system kept making a rattling noise. When cleaning the condenser, I found that the bolts that mount the compressor to the base pan became loose. I removed the bolts to ensure nothing became stripped and reinstalled. Started up the system and the rattling noise went away. Indoor zone dampers are opening and closing as designed. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time.

Performed AC cool check on three systems. Checked electrical, mechanical, safety, and performance of the systems. Drain lines were cleared and treated. The wiring is tight and in good condition. Refrigerant charge is within factory specifications. Capacitors and condenser fan motors are also in good condition. Contactors are good and I sprayed some JS insecticide around them to help prevent ants. The two air handlers in the upper attic have some mold/mildew spots. Options for repair were presented to the customer and they chose to have system sterilizers installed in two of the systems. I installed the system sterilizers and function checked the systems. They were both running at the time of departure.

Performed semiannual maintenance on one heat pump cooling unit. Inspected all Performance, Mechanical and Safety Systems. Flushed and treated the primary drain line and ensured all surge protection devices were on and green lit as designed. Did find that the outdoor condenser exhaust fan motor is leaking oil and beginning to reach max amperage per the motor data tag. Recommended replacing the motor to ensure the cooling and heating unit stays running at 100% capacity. Spoke with homeowner and we have decided to go ahead and replace the outdoor fan motor now rather than waiting for it to seize up. Installed new fan motor outside and programmed the motor to match the direction and speed of the factory motor. Reset the AC system and tested. Verified everything was operating as designed. Everything is working at this time.

Replaced the secondary drain pan. Added a water safety switch to the evaporator coil. Rebuilt the condensate drain line. Cleared and treated the drain. Replaced the outdoor condenser fan motor. Removed the bypass duct and sealed up the spots where it was originally located. Replaced the indoor TXV. Pressure tested with dry nitrogen and pulled a vacuum on the copper line set. Charged system to factory spec. System is working properly at this time.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared, and flow tested with water. I then treated the drain line. The air handler and blower wheel are clean. The evaporator coil is also clean. The condenser fan motor and capacitor are in good condition. Refrigerant charge is within factory specifications. Condenser coil cleaned. No major issues were found, and the system was running at the time of departure.

Master Bedroom HVAC System: Found the emergency water safety switch tripped due to a restricted primary drain line that attaches to the right master bathroom sink. Blew out the drain line and flushed and treated lime to verify proper drainage. Cleaned out the primary pan to ensure no residual gunk enters back into the drain line. Reset the cooling system and verified operation. Everything is working at this time.

Installed Carrier gas system. Installed Ecobee thermostat. Transitioned to existing supply plenum. Rebuilt and insulated primary drain line. Installed SS2 safety float switch. Cleared and verified drain operation. Installed plywood overlay and sealed all connections with mastic airlock. Replaced disconnect and whip at outdoor condenser. Pressure tested and pulled a vacuum on the line set. Verified system charge was to manufacturers specifications.

Performed service diagnostic. Diagnostic found that the condensate drain line was clogged. Recent storms had plugged the drain line with yard debris. Options for repair were presented to the customer and she chose to have the drain line cleared today. I cleared the drain line and flow tested it with water. I also positioned the brick holding the drain line out of the dirt. I treated the drain and function checked the system. The system was running at the time of departure.

Performed service diagnostic. Diagnostic found that the condensate drain line was clogged and the capacitor on the condenser unit was below value. The drain line was cleared and treated. The capacitor on the condenser unit was replaced. I performed an AC cool check on the system and no other major issues where found. System as running at the time of departure.

Performed semiannual maintenance on one heat pump cooling system. Inspected all Performance, Mechanical and Safety Systems. Changed out one 20x25x4 air filter. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time.

Installed new Carrier 2-ton gas two stage system. Installed new Ecobee Pro thermostat. Rebuilt and insulated condensate drain line. Added SS2 and SS3 safety float switches. Replaced both supply and return plenums and sealed with a mastic airlock. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Replaced the disconnect and ran the low voltage in Seal-Tite. Charged system to factory spec and performed a benchmark. System is working properly at time of departure.

I cleared the drain and also rinsed the outdoor unit out. I checked over the system and found everything to be in pretty good shape. I did discover that the refrigerant was a bit high after I completely disassembled and cleaned the outdoor unit. I removed refrigerant to get down to the 11 degrees of sub cooling it asks for on the data tag. System is in working order at completion of appointment

I cleared the drain and also rinsed the outdoor unit out. I checked over the system and found everything to be in pretty good shape. I did discover that the refrigerant was a bit high after I completely disassembled and cleaned the outdoor unit. I removed refrigerant to get down to the 11 degrees of sub cooling it asks for on the data tag. System is in working order at completion of appointment

I cleared the drain and also rinsed the outdoor unit out. I checked over the system and found everything to be in pretty good shape. I did discover that the refrigerant was a bit high after I completely disassembled and cleaned the outdoor unit. I removed refrigerant to get down to the 11 degrees of sub cooling it asks for on the data tag. System is in working order at completion of appointment

I cleared the drain and also rinsed the outdoor unit out. I checked over the system and found everything to be in pretty good shape. I did discover that the refrigerant was a bit high after I completely disassembled and cleaned the outdoor unit. I removed refrigerant to get down to the 11 degrees of sub cooling it asks for on the data tag. System is in working order at completion of appointment

I rinsed the condenser coil and ensured the drain line was clear. I also cleaned out the reservoir for the condensate pump. I checked over the system and discovered the following: the capacitor is almost dead and the system is low on refrigerant. Customer elected to proceed with my top option. Details are as follows: “Includes replacement of the capacitor and charging of the system with up to 3 pounds of refrigerant.” I charged the system up to 11 degrees of sub cooling first and then replaced the capacitor after the unit was charged. System is in working order at completion of appointment.

I rinsed the condenser coil and ensured the drain line was clear. I also cleaned out the reservoir for the condensate pump. I checked over the system and discovered the following: the capacitor is almost dead and the system is low on refrigerant. Customer elected to proceed with my top option. Details are as follows: “Includes replacement of the capacitor and charging of the system with up to 3 pounds of refrigerant.” I charged the system up to 11 degrees of sub cooling first and then replaced the capacitor after the unit was charged. System is in working order at completion of appointment.