HVAC Service In Buda, TX

Arrived to find the indoor unit blowing air but the outside condenser not running. Performed diagnostic on system. Checked the emergency float switch coming off of the secondary and found that it was full of water tripping the float switch. Cleared the drain line with CO2 and used my vacuum on the exterior penetration near the condenser to remove any additional clogging. System is cooling properly upon completion of repairs.

Upon arrival, the homeowner stated there was a noise coming from the outside condenser. I cycled the system multiple times but was unable to replicate the noise. I continued diagnostic of the system and found that the float switch was tripped due to the primary drain being clogged. I presented repair options and the homeowner agreed to have him take care of the clogged drain. They also decided to sign up for our maintenance plan. I cleared and treated the drain line. System now operational.

On arrival I found that the house was at the set temperature. The system was running and was cooling at 12 degrees of sub cooling. There were some dead weeds in the condenser coil so I pulled them out. A further diagnostic of the system found that the capacitor on the condenser unit was well below value on the fan terminal. The 5 micro farad capacitor was only reading 3 nano farads. Options for repair were presented to customer and he chose to have the capacitor replaced today. I replaced the capacitor and rinsed the dirt off the condenser coil. I then function checked the system. The system is running at the time of departure.

Performed semiannual maintenance on one straight cool AC system. Inspected all Performance, Mechanical and Safety systems. Flushed and treated the primary drain line that attaches to the right-side master bathroom sink. Verified everything is working within manufacture’s specifications for operation. Everything is working at this time.

Kitchen Side HVAC System: On arrival, I spoke with Ms. Sanderson, and she stated that the AC unit will not keep the house to the desired temperature. I went into the attic through the garage access and found that the air handler emergency drain pan is filled with water and that the primary drain line is backed up too. This caused the emergency water safety switch to trip which then caused the thermostat to blink and cycle on and off. Recommend that we remove all the standing water inside the emergency drain pan and then follow that with cleaning and clearing the primary drain line. Spoke with homeowner and we went ahead and decided to move forward with the drain cleaning. I removed all standing water from the emergency drain pan and then cleared out the primary drain line. Added in a drain treatment into the line to help with proper drainage. Reset the AC system and verified operation. Everything is working at this time.

Cool check completed on an up-flow gas system with inverter. Indoor unit clean and air filter clean. The drain line has been cleared and treated. The float switch was checked and is working properly. Outdoor coils cleaned. All electrical within range. Refrigerant levels are also within range. No major issues were found, and the system is functioning properly at this time.

Installed both upstairs and downstairs systems. Installed two Honeywell thermostats. Installed new supply and return air plenums. Rebuilt and insulated both primary drain lines. Replaced secondary drain pans. Added SS2 and SS3 safety float switches to both units and verified drain operation. Replaced disconnect and whips at outdoor condensing units. Pressure tested and pulled a vacuum on both line sets. Weighed in charge for both systems to match manufacturer specifications.

I made sure to rinse the condenser coil as well as clear and treat the drain. I performed a full evaluation of the AC side of the system and found everything to be in great shape. Refrigerant charge is proper and all of the minor components on the system are working properly. No recommendations were made at this time. System is in working order at completion of appointment.

I made sure to rinse the condenser coil as well as clear and treat the drain. I performed a full evaluation of the AC side of the system and found everything to be in great shape. Refrigerant charge is proper and all of the minor components on the system are working properly. No recommendations were made at this time. System is in working order at completion of appointment.

I made sure to rinse the condenser coil as well as clear and treat the drain. I performed a full evaluation of the AC side of the system and found everything to be in great shape. Refrigerant charge is proper and all of the minor components on the system are working properly. No recommendations were made at this time. System is in working order at completion of appointment.

I made sure to rinse the condenser coil as well as clear and treat the drain. I performed a full evaluation of the AC side of the system and found everything to be in great shape. Refrigerant charge is proper and all of the minor components on the system are working properly. No recommendations were made at this time. System is in working order at completion of appointment.

On arrival the customer informed me that their thermostat went blank this morning and their A/C has not worked since then. I performed an inspection of the system and found that the 3-amp fuse had blown. I shut power off at the breaker confirmed all low and high voltage connections were tight. Thermostat connections are also tight. I did find a small rub out on the wire coming from the water safety switch into the air handler. I stripped back the new wire and connected it with a wire nut. I reset the breaker and cycled power at the thermostat multiple times. No other major issues were found. The system is operational at this time.

Performed semiannual maintenance on one heat pump cooling system. Inspected all Performance, Mechanical and Safety Systems. Customer had an extra AprilAire 310 filter on hand that we went ahead and changed out. Flushed and treated the primary drain line and verified everything is currently operating within manufacture’s specifications for operation. No major issues found.

I made sure to clear the drain and treat it as well as rinse the outdoor unit. During my evaluation of the system I discovered the following: the system is R-22 and low on refrigerant, the contactor is pitted and charred, and the float switch has failed. I brought all of this to the attention of the customer and made him a few options. He did elect to have me replace the failed float switch in the attic. I installed and tested the float to ensure it works properly. System is working to the best of its ability at this time.

I made sure to clear the drain and treat it as well as rinse the outdoor unit. During my evaluation of the system I discovered the following: the system is R-22 and low on refrigerant, the contactor is pitted and charred, and the float switch has failed. I brought all of this to the attention of the customer and made him a few options. He did elect to have me replace the failed float switch in the attic. I installed and tested the float to ensure it works properly. System is working to the best of its ability at this time.

I made sure to clear the drain and treat it as well as rinse the outdoor unit. During my evaluation of the system I discovered the following: the system is R-22 and low on refrigerant, the contactor is pitted and charred, and the float switch has failed. I brought all of this to the attention of the customer and made him a few options. He did elect to have me replace the failed float switch in the attic. I installed and tested the float to ensure it works properly. System is working to the best of its ability at this time.

I made sure to clear the drain and treat it as well as rinse the outdoor unit. During my evaluation of the system I discovered the following: the system is R-22 and low on refrigerant, the contactor is pitted and charred, and the float switch has failed. I brought all of this to the attention of the customer and made him a few options. He did elect to have me replace the failed float switch in the attic. I installed and tested the float to ensure it works properly. System is working to the best of its ability at this time.

Performed cooling maintenance on one heat pump system. Checked all electrical mechanical and performance of the system. Cleared and treated the drain line. Removed leaves from inside of condenser and then rinsed off coils. Customer supplied filter for replacement. No major issues were found, and the system is operational at this time.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The underside of the evaporator coil is dirty. The drain line was cleared and treated. The condenser coil was cleaned. The contractor is in good condition and so is the condenser fan motor. The capacitor is within value. The system is reaching the set temperature, and it was 69 degrees inside the home. No other major issues were found, and the system was running at the time of departure

Performed AC cool check on a Carrier Infinity system. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The air handler blower wheel and evaporator coil are clean. The wiring is tight and in good condition. Condenser coil clean. Refrigerant levels are within manufacture specifications. No major issues were found, and the system is running at the time of departure.