HVAC Service In Buda, TX

Performed cooling maintenance on two systems. Checked all electrical, mechanical and performance of both systems. Cleared and treated both drain lines and washed both outdoor coils. Filters were replaced by the customer last month and are clean. I found the wire nuts on the furnace for the incoming high voltage were undersized on both systems. I replaced them with the correct size and cycled both systems at the thermostat. Both systems are operational at this time.

Performed semiannual maintenance on one heat pump cooling system. Inspected all Performance, Mechanical and Safety Systems. I changed out one 20x25x4 Honeywell air filter in the attic provided by the homeowner. I cleared and treated the primary drain line that attaches onto the master bathroom sink. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time.

Performed AC cool check on three systems. Checked electrical, mechanical, safety, and performance of the systems. Drain lines were cleared and flow tested with water. Drain lines were then treated. The blower wheels are clean. Electrical wiring is tight and in good condition. The condenser fan motors and contactors are also in good condition. All capacitors are within value. The refrigerant charges are within factory specifications. All systems are cooling at about 10 degrees of sub cooling. No other major issues were found, and the systems are running at the time of departure.

Performed semiannual maintenance on one heat pump cooling system. Inspected all Performance, Mechanical and Safety Systems. Flushed and treated the primary drain line, cleaned the outdoor condensing coil, and ensured all Surge Protection Devices and the Stage 3 Breathe Easy System are on and running as designed during our visit. Found everything to be operating within manufacture’s specifications for operation. Everything is working at this time.

Single system cool check performed. The air handler is clean. The drain line was cleared and treated. I checked the float switch, and it is operational. Outdoor coils cleaned. All electrical within manufactures specs. Refrigerant level also with manufactures specs. No major issues found, and the system is operating properly at this time.

Built and installed new return and extended supply plenum. Installed Media air filter and sealed all connections with air lock and mastic tape. Home ran all three ducts to the supply plenum without using the wye. Also installed our Stage 3 Breathe Easy Package and cleared the drain and verified operation.

I arrived at the home to find the system off. I spoke to homeowner about how the units had been operating. I made sure to pull and clean the filters on the Minisplit and rinse off the condenser. I then made sure to rinse the condenser and clear the drain of the main house system. I checked over both units and found everything to be in good working order. All of the minor and major parts checked out fine. System is in working order at completion of appointment.

I arrived at the home to find the system off. I spoke to homeowner about how the units had been operating. I made sure to pull and clean the filters on the Minisplit and rinse off the condenser. I then made sure to rinse the condenser and clear the drain of the main house system. I checked over both units and found everything to be in good working order. All of the minor and major parts checked out fine. System is in working order at completion of appointment.

I arrived at the home to find the system off. I spoke to homeowner about how the units had been operating. I made sure to pull and clean the filters on the Minisplit and rinse off the condenser. I then made sure to rinse the condenser and clear the drain of the main house system. I checked over both units and found everything to be in good working order. All of the minor and major parts checked out fine. System is in working order at completion of appointment.

I arrived at the home to find the system off. I spoke to homeowner about how the units had been operating. I made sure to pull and clean the filters on the Minisplit and rinse off the condenser. I then made sure to rinse the condenser and clear the drain of the main house system. I checked over both units and found everything to be in good working order. All of the minor and major parts checked out fine. System is in working order at completion of appointment.

Two system cool check completed. Both indoor units are clean. The low-voltage wires were tightened. The drain lines have been cleared and treated. The float switches were checked and are working properly. Both condensers have clean coils. The amp draws are all within range. The contractors are in fair condition. The refrigerant level on both units are within range. I found both capacitors well below manufacture specs and have recommended they be replaced. The customer has agreed to have both capacitors replaced at this time. I replaced both capacitors and checked the system again. No other major issues were found and both systems are operating properly at this time.

Replaced the indoor mini split head on the pool house. Reconnected the electrical, copper line set and drain line. Pressure tested with dry nitrogen and pulled a vacuum on the system. Charged system with new refrigerant and checked operation of the system. Insured proper drainage of the indoor unit. The system is working at this time.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. A small amount of dust was found on the blower wheel and coil. The wiring is tight and in good condition. The condenser fan motor and contactor are in good condition. The refrigerant charge is within factory specifications. Capacitor is within value. No major issues were found, and the system is running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared, and flow tested with water. The drain line was treated. The blower wheel and evaporator coil are clean. The wiring is tight and in good condition. Reme-Halo air purifier is operational. The condenser coil is clean. The condenser fan motor and contactor are in good condition. The condenser capacitor is within value. The refrigerant charge is within factory specifications. No major issues were found, and the system is running at the time of departure.

Performed service diagnostic. Diagnostic found that the capacitor on the condenser unit has failed. Options for repair were presented to the customer and she chose to have the capacitor replaced today. I replaced the capacitor and function checked the system. System was running at the time of departure.

Performed semiannual maintenance on one heat pump cooling system. Inspected all Performance, Mechanical and Safety Systems. Flushed and treated the drain line and cleaned the outdoor condensing coils. Everything is operating within the manufacturer’s specifications for operation.

Installed the new blower motor and furnace control board. Checked the operation of the system and it is working at this time.

Performed cooling maintenance on one heat pump system. Checked all electrical, mechanical, and performance of the system. Cleared and treated the drain line and washed the outdoor coil. The filter was replaced by the customer prior to my arrival. I did find that the outside condenser unit does not have any surge protection installed. I presented my findings to the homeowner, and he decided to have one installed today. I installed the surge protector, reset the breaker and cycled power at the thermostat. The system is operational at this time.

Performed cooling maintenance on one furnace system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I did find the high voltage wire nuts were the incorrect size at the furnace. I replaced them with the correct size and secured them with electrical tape. No other major issues were found, and the system is operational at this time.

Installed new evaporator coil. Brought the service side to the front of the system. Sealed the coil to the furnace and the supply plenum. Rebuilt the condensate drain line and insulated the PVC. Added SS2 and SS3 safety float switches. Cleared and treated the condensate drain line. Moved the filter dryer into the attic. Pressure tested and pulled a vacuum on the copper line set. Install surge protection on the condenser disconnect. Charged the system with new refrigerant and checked over the operation of the system. The system is working properly at this time.