HVAC Service In Buda, TX

Performed semiannual maintenance on two heat pump heating systems. Inspected all Performance, Mechanical and Safety Systems. Verified everything to be operating within manufacture’s specifications for operation. Changed one 20x25x4 in the main house and the homeowner will purchase a 20x20x4 for the office HVAC system. Everything is working at this time. See attached checklists for full tune-up details.

Removed the failing inducer motor and the failed flame rod. Installed new flame sensor and installed new inducer motor. Also installed new screws inside the furnace exhaust piping to ensure a proper and secure fit going out the roof penetration. Tested the new flame rod and verified the proper micro amps were being produced. Tested the electrical power reading of the new inducer motor and verified it was within the manufactures specifications for operation. Everything is working at this time.

Performed semiannual maintenance on one gas furnace heating system. Inspected all Performance, Mechanical and Safety Systems. Tested and verified all zone dampers are opening/closing as designed. Adjusted fuel pressure to match system output rating. All Breathe Easy Systems are on and operating as designed. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time. See attached checklist for full tune-up details.

Performed semiannual maintenance on one gas furnace heating system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation. Also verified that all Breathe Easy Systems and all Surge Protection Devices are on and operating as designed. Everything is working at this time. See attached checklist for full tune-up details.

During my evaluation of the system, I discovered the following: the condenser fan motor is overamping, the filter needs to be replaced, and the maintenance agreement is expiring. See attached checklist for full tune-up details. I brought all of this to the attention of the homeowner and wrote up a list. She elected to perform every task on the list. I left and returned with new filters. I installed a new Perfect Fit filter and discovered that 2 of the 4 locking tabs are broken off. We are unable to replace the entire assembly due to not being able to get that part anymore. For the time being the sides without a tab are duct taped down. I also replaced the condenser fan motor. I made sure to get everything nice and tight with the motor and installed the motor protector. I tested the system after the repairs were completed and everything ran properly. I also made sure to wire one side of 240 to come out of the defrost control board. System is in working order at completion of

During my evaluation of the system, I discovered the following: the condenser fan motor is overamping, the filter needs to be replaced, and the maintenance agreement is expiring. See attached checklist for full tune-up details. I brought all of this to the attention of the homeowner and wrote up a list. She elected to perform every task on the list. I left and returned with new filters. I installed a new Perfect Fit filter and discovered that 2 of the 4 locking tabs are broken off. We are unable to replace the entire assembly due to not being able to get that part anymore. For the time being the sides without a tab are duct taped down. I also replaced the condenser fan motor. I made sure to get everything nice and tight with the motor and installed the motor protector. I tested the system after the repairs were completed and everything ran properly. I also made sure to wire one side of 240 to come out of the defrost control board. System is in working order at completion of

During my evaluation of the system, I discovered the following: the condenser fan motor is overamping, the filter needs to be replaced, and the maintenance agreement is expiring. See attached checklist for full tune-up details. I brought all of this to the attention of the homeowner and wrote up a list. She elected to perform every task on the list. I left and returned with new filters. I installed a new Perfect Fit filter and discovered that 2 of the 4 locking tabs are broken off. We are unable to replace the entire assembly due to not being able to get that part anymore. For the time being the sides without a tab are duct taped down. I also replaced the condenser fan motor. I made sure to get everything nice and tight with the motor and installed the motor protector. I tested the system after the repairs were completed and everything ran properly. I also made sure to wire one side of 240 to come out of the defrost control board. System is in working order at completion of

During my evaluation of the system, I discovered the following: the condenser fan motor is overamping, the filter needs to be replaced, and the maintenance agreement is expiring. See attached checklist for full tune-up details. I brought all of this to the attention of the homeowner and wrote up a list. She elected to perform every task on the list. I left and returned with new filters. I installed a new Perfect Fit filter and discovered that 2 of the 4 locking tabs are broken off. We are unable to replace the entire assembly due to not being able to get that part anymore. For the time being the sides without a tab are duct taped down. I also replaced the condenser fan motor. I made sure to get everything nice and tight with the motor and installed the motor protector. I tested the system after the repairs were completed and everything ran properly. I also made sure to wire one side of 240 to come out of the defrost control board. System is in working order at completion of

Performed maintenance on one heat pump system. Checked electrical, mechanical, safety, and performance of the system. All heat strips activated. Filters were dirty and were changed with customer supplied filters. Blower wheel and coil are both clean. Drain line was clear. Outside condenser refrigerant pressures within range and condenser was clean. Capacitor was within value. During my maintenance, I noticed that the condenser fan motor is showing severe signs of overheating. I brought this to the homeowner’s attention, but they declined repairs today. No other major issues were found, and the system was running at the time of departure. See attached checklist for full tune-up details.

Performed heater maintenance on one gas furnace. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved and flame sensor cleaned. Filter was clean as it was recently changed by the homeowner. Blower and coil are clean. Drain line was clear. No major issues were found and system running at time of departure. Gas valves confirmed on. See attached checklist for full tune-up details.

Service diagnostic found that the igniter was cracked/broken. Options for repair were presented to the customer and they chose to have the igniter replaced and sign up for maintenance. Igniter was replaced and the system was function checked. System was running at the time of departure.

Downstairs HVAC System: On arrival I spoke with the homeowner who showed me that the thermostat was frozen and became unresponsive to the touch screen. I tried changing the batteries and cleaning the corrosion off but was still unable to get the thermostat working again. I showed her a couple of thermostat options I had and she chose to have the thermostat replaced with. I installed a new thermostat and programmed it to match the equipment type installed. Tested all modes and verified the system was operational at time of departure.

Performed semiannual maintenance on one gas furnace and one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation. Did not see anything that would cause the heater to not work properly on the apartment system. Everything is working at this time. See attached checklist for full tune-up details.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. I did change out one AprilAire 910 Filter as the previous one has become dirty and was beginning to create an airflow restriction. Tested and verified that the heat pump system was operating within manufacture’s specifications for operation. Everything is working at this time. See attached checklist for full tune-up details.

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I found that the heat kit has failed. I informed the homeowner of the situation and presented options for repair; he chose to have it replaced at this time. I replaced the heat kit and cycled power at the thermostat. No other major issues were found, and the system is operational at this time. See attached checklist for full tune-up details.

Performed heater check on a Carrier gas furnace. Checked electrical, mechanical, safety, and performance of the system. Air handler and evaporator coil are clean. Blower wheel is also clean. Auxiliary heat kit is operational and all strips drawing normal amperage. Drain line was cleared and treated. Capacitor on the condenser is in value and the condenser fan motor is in good condition. Contactor and electrical connections are also good. Condenser coil cleaned. Electrical disconnect confirmed in and on. System was running at the time of departure. See attached checklist for full tune-up details.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. I did note that the underside of the evaporator coil is becoming restricted due to a buildup of dirt and debris. Went through and verified all systems were operating within manufacture’s specifications for operation. Everything is working at this time. See attached checklist for full tune-up details.

Performed heater maintenance on one heat pump system. Checked electrical, mechanical, safety, and performance of the system. All three heat strips heating upon test. Filters were clean as they were recently replaced by homeowner. Indoor blower and coil are both clean. Outside condenser refrigerant pressure within range and condenser clean. No major issues were found, and the system was running at time of departure. See attached checklist for full tune-up details.

Installed new 3-ton Carrier gas system. Installed new Ecobee Pro thermostat. Installed new extended supply plenum and sealed with mastic air lock. Reused return plenum since it was recently installed. Replaced secondary drain pan. Ran new wire to the thermostat. Installed new liquid line filter dryer. Pressure tested line set with nitrogen and pulled a vacuum on the line set. Rebuilt and insulated condensate drain line. Added SS2 and SS3 safety float switches. Cleared drain and verified operation. Tested system in heating and cooling and weighed in refrigerant to manufacturers specifications.

Performed heating maintenance on one furnace system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line. Filters were replaced by the customer recently. No major issues were found and system is operational at this time. See attached checklist for full tune-up details.