HVAC Service In Buda, TX

Performed heater check on a Lennox gas furnace. Checked electrical, mechanical, safety, and performance of the system. Return and supply ducts are clean. Blower wheel and air handler are also clean. Blower motor capacitor is within value. Drain line was cleared and treated. Igniter is in value and operational. Flame sensor was cleaned. Inducer motor is running at normal amperage. One of the wires for the safety switches was hanging loose inside the air handler. I secured the wire. I also found that a small section of insulation on the condensation drain had come loose and part of the line was uninsulated. I wrapped the exposed section of pipe with foam tape. No other major issues were found. System was set to customer’s desired temperature and was running at the time of departure. See attached checklist for full tune-up details.

Performed a heating tune-up on two Lennox heat pump systems. I checked over both electrical systems and ensured everything was tight. I checked the air handlers for cleanliness and found that both coils are clean however the blower wheels did have buildup on them. I also found the run capacitor for the bedroom system is below value. Both drain lines were cleared. I then turned on each system and performed operational testing. I let each system run and put my probes on the outside condensers to check refrigerant pressures. I found refrigerant pressures to be within manufacture specifications on both systems. Both condensers are clean as well. I did find that the condenser fan motor on the bedroom system is showing severe signs of overheating. After completing my operational test over both systems, I then compiled a list of the deficiencies I found and presented them to the homeowner. He decided to move forward with the most critical repairs which was a new condenser fan motor and

Performed heater check on a Rheem gas furnace. Checked electrical, mechanical, safety, and performance of the system. Drain line was cleared and treated. Filter was replaced with a customer supplied filter. Return and supply ducts are clean. Flame sensor was cleaned. Blower wheel is clean. Spark ignition is operational, and the inducer motor is running at normal amperage. Both zone dampers are operational. No major issues were found, and the system was running at the time of departure. See attached checklist for full tune-up details.

Performed heater check on a Carrier gas furnace. Checked electrical, mechanical, safety, and performance of the system. Return and supply ducts are clean. Some dust is beginning to collect on the filter bases. I dusted the filter bases and sealed the filters with painter’s tape to help with filter bypass. Flame sensor was cleaned and is in good condition. Igniter is within value and is operational. Inducer motor is drawing normal amperage and is operational. Drain line was cleared and treated. No major issues were found and the system is running at the time of departure. See attached checklist for full tune-up details.

Performed semiannual maintenance on one gas furnace heating system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time. See attached checklist for full tune-up details.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. Changed one homeowner supplied Honeywell 20x20x4 F100 Filter. Flushed and treated the primary drain system. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time. See attached checklist for full tune-up details.

Performed heating maintenance on one gas furnace. After opening up unit I checked over the electrical components to ensure everything was tightened down. I checked the blower wheel for cleanliness and found no issues. After inspecting the flame sensor, I noticed scorch marks on the surface that seem to be affecting the system’s operation. After finding this deficiency, I brought it to the attention of the homeowner. He decided to move forward with the repair. I replaced the scorched flame sensor with a clean new one. I then hooked my meter up to the gas valve and I turned the system on for an operational test. Everything is operational and within manufacture specifications. System is operational at time of departure. Gas valves confirmed on. See attached checklist for full tune-up details.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. Ensured the Stage 3 Breathe Easy System was on and operating as designed. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time. See attached checklist for full tune-up details.

I arrived at the home to find the system on and running. I spoke to the homeowner about how the systems had been performing. I made sure to clean the flame sensor on the furnace. I checked over the systems and discovered the following: Main House System: The igniter is pitted and worn, the blower motor is leaking oil, the inducer bearings are starting to make noise, and the blower wheel is dirty. Shed: This system is working fine and has no issues. I showed the homeowner how to pull and clean the filters.

I arrived at the home to find the system on and running. I spoke to the homeowner about how the systems had been performing. I made sure to clean the flame sensor on the furnace. I checked over the systems and discovered the following: Main House System: The igniter is pitted and worn, the blower motor is leaking oil, the inducer bearings are starting to make noise, and the blower wheel is dirty. Shed: This system is working fine and has no issues. I showed the homeowner how to pull and clean the filters.

I arrived at the home to find the system on and running. I spoke to the homeowner about how the systems had been performing. I made sure to clean the flame sensor on the furnace. I checked over the systems and discovered the following: Main House System: The igniter is pitted and worn, the blower motor is leaking oil, the inducer bearings are starting to make noise, and the blower wheel is dirty. Shed: This system is working fine and has no issues. I showed the homeowner how to pull and clean the filters.

I arrived at the home to find the system on and running. I spoke to the homeowner about how the systems had been performing. I made sure to clean the flame sensor on the furnace. I checked over the systems and discovered the following: Main House System: The igniter is pitted and worn, the blower motor is leaking oil, the inducer bearings are starting to make noise, and the blower wheel is dirty. Shed: This system is working fine and has no issues. I showed the homeowner how to pull and clean the filters.

Performed heater check on a Carrier heat pump system. Checked electrical, mechanical, safety, and performance of the system. Drain line was cleared and flow tested with water. Drain line was then treated. Air handler and blower wheel are both clean. Return and supply ducts are also clean. Auxiliary heat strips are all operational and running at 18.8 amps. Condenser capacitor is in value and the condenser fan motor is in good condition. Condenser coil clean. No major issues were found and the system was running at the time of departure. See attached checklist for full tune-up details.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation.

Replaced the existing mini split with a new Carrier system. Ran new copper line set. Ran new control wiring. Replaced the disconnect at the condenser. Pressure tested the copper line set and pulled a deep vacuum. Tested the operation of the system and it is working properly.

Performed heater check on an American Standard heat pump. Return and supply ducts are clean. Evaporator coil and blower wheel are also clean. Drain line was cleared and flow tested with water. Drain line was treated. Electrical heat strips are operational. Condenser capacitor is within value. Condenser fan motor is showing signs of overheating. No other major issues were found. See attached checklist for full tune-up details.

Service diagnostic found that the condenser fan motor has failed. Options for repair were presented to the customer and they chose to have the motor replaced. I replaced the condenser fan motor and function checked the system. The system is now operating normally.

Performed heating tune-up on one American Standard heat pump. Checked all of wiring and electrical components. Cleared drain line. Customer had a replacement Perfect Fit filter which I swapped for the dirty one. Looked over the coil for any rust, dirt or mold but I found the coil to be clean. I did find some buildup on the blower wheel though. I then turned the system on and performed an operations check. I went outside and attached my probes and found the refrigerant to be within specifications. I did find the capacitor to be slightly below value though. I brought my findings to the homeowner, and he chose to have the capacitor replaced and the blower wheel cleaned. I completed repairs and performed another check of the system. No other major issues found, and the system was operational at time of departure. See attached checklist for full tune-up details.

Completed tune-up on one Carrier heat pump system. Checked wiring and electrical components. Check over the cleanliness of the coil as well as the blower wheel and I found no build up on either. I changed the filter with a customer supplied filter. I then cleared the drain line. After that I turned the system on for an operational test. All three of the heat strips came on with no issue. Went outside to the outdoor condenser and attached gauge probes. I let the system run and I verified that the refrigerant pressures are within range for manufacture specifications. I found the capacitor to be within value. I found no issues with the fan motor or contactor and the outside condenser is clean. No major issues were found, and the system was running at time of departure. See attached checklist for full tune-up details.

Performed heater check on a Carrier heat pump. Checked electrical, mechanical, safety, and performance of the system. Drain line was cleared and flow tested with water. Drain line was treated. The evaporator coil and air handler are clean. Blower wheel is also clean. System sterilizers and surge protection are operational. Emergency heat strips are operational. Condenser capacitor is within value and the condenser fan motor is in good condition. I sealed door panel to the air handler with tape to ensure no attic air was leaking into the system. No major issues were found and the system was running at the time of departure. See attached checklist for full tune-up details.