HVAC Service In Buda, TX

I installed one UV light going perpendicular across the top of the A-coil. I installed the other light inside the A-coil. I then installed the power pack and the surge protector on the main circuit of the air handler. I then replaced the blower motor. I tested everything and cycled the system. The blower motor now turns off properly. The UV lights and surge protector are working properly. System is in working order at completion of appointment.

I installed one UV light going perpendicular across the top of the A-coil. I installed the other light inside the A-coil. I then installed the power pack and the surge protector on the main circuit of the air handler. I then replaced the blower motor. I tested everything and cycled the system. The blower motor now turns off properly. The UV lights and surge protector are working properly. System is in working order at completion of appointment.

Performed semiannual maintenance on one gas furnace heating system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time. See attached checklist for full tune-up details.

I ended up checking the outdoor unit in cooling mode due to the temperatures being high today. I checked over the entire system on the heating/cooling side and found the system to be in great shape. System is in working order at completion of appointment. See attached checklist for full tune-up details.

I ended up checking the outdoor unit in cooling mode due to the temperatures being high today. I checked over the entire system on the heating/cooling side and found the system to be in great shape. System is in working order at completion of appointment. See attached checklist for full tune-up details.

I ended up checking the outdoor unit in cooling mode due to the temperatures being high today. I checked over the entire system on the heating/cooling side and found the system to be in great shape. System is in working order at completion of appointment. See attached checklist for full tune-up details.

I ended up checking the outdoor unit in cooling mode due to the temperatures being high today. I checked over the entire system on the heating/cooling side and found the system to be in great shape. System is in working order at completion of appointment. See attached checklist for full tune-up details.

Performed heater check on a Lennox gas furnace. Checked electrical, mechanical, safety, and performance of the system. Drain line was cleared and treated. Blower motor capacity is below value. Return and supply ducts are clean. Blower wheel is also clean. Igniter is operational and in value. Flame sensor was cleaned. Inducer motor is drawing normal amperage. No other major issues were found. See attached checklist for full tune-up details.

Recovered all refrigerant from the system and removed the compressor. Replaced one-way liquid line dryer and pressure tested system for extensive leak check. Pulled deep vacuum and weighed in factory charge. I did speak with the homeowner about installing an outdoor surge protector to help protect the new compressor; they chose to have one installed. Verified system operation and rinsed out condenser coil. I also cleaned out the leaves and sprayed ant deterrent. System operating at this time.

Performed heater check on a Carrier electrical heat system. Checked electrical, mechanical, safety, and performance of the system. Drain line was cleared and treated. Filter was replaced with a customer supplied filter. Return and supply ducts are clean. The evaporator coil, blower wheel and air handler are also clean. The heat kit is operational and all strips working properly. Electrical heat strips were running at 19 amps. Control wiring was tightened. Condenser coil clean. The condenser fan motor is in good condition. Surge protection is operational. Disconnect is in good condition and the capacitor for the condenser unit is within value. No major issues were found, and the system was set to the customer’s desired temperature. See attached checklist for full tune-up details.

Performed semiannual maintenance on one heat pump mini split in cottage. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time. See attached checklist for full tune-up details.

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I presented options for nice to have items and the homeowner chose to just have a surge protector installed at the outdoor unit. I installed the surge protector and cycled power at the thermostat. No major issues were found, and the system is operational at this time. See attached checklist for full tune-up details.

Performed heat check on a Lennox heat pump. Checked electrical, mechanical, safety, and performance of the system. Drain line was cleared and treated. Return and supply ducts are clean. The evaporator coil and air handler are also clean but I did find some buildup on the blower wheel. The auxiliary heat kit is operational, and all strips are working. Amp draw on the heat strips was 20 amps. Zone control dampers are operating normally. Condenser coil clean. Condenser capacitor is within value. The condenser fan motor is in good condition. Condenser disconnect is also in good condition. No other major issues were found, and the system was set to the customer’s desired temperature. See attached checklist for full tune-up details.

Performed heat check on a York gas furnace. Checked electrical, mechanical, safety, and performance of the system. Drain line was cleared and treated. Filters were replaced with customer supplied filters. Return and supply ducts are clean. Blower wheel is also clean. Blower motor capacitor is within value. Flame sensor was cleaned and is operational. Igniter is in value and operational. Inducer motor is running at normal amperage. No major issues were found. System was set to the customer’s desired temperature and was running at the time of departure. See attached checklist for full tune-up details.

Completed a heating check for one electric heat system. I opened up the inside system and began checking over the electrical components. I then checked over the blower wheel and coil and found both to be clean. The UV light installed in the air handler is operational. Drain line was cleared and treated. Filters are in clean condition. After my initial checks were completed, I turned the system on and performed an operational test. All heat strips activated with correct voltage. While the system ran, I cleaned out the closet. No major issues found, and the system is operational at time of departure. See attached checklist for full tune-up details.

Completed a heating tune-up on one heat pump. Checked all electrical components. Drain line cleared and treated. Filter is slightly dirty, but the homeowner stated they changed it out recently. The blower wheel and coil are clean. I turned the system on for an operational test. While allowing the system to run for a bit, I cleaned out the closet with my vacuum. Continued check of the system and found that both heat strips are operational. I then went outside to check the heat pump. I attached my gauges to the condenser to check refrigerant pressures and found them to be within spec. While the panel was off, I cleaned out the electrical area. The outside of the condenser is already clean. Capacitor and contactor are both within value. No major issues were found, and everything is operational time of departure. See attached checklist for full tune-up details.

I arrived and got straight to work. I removed the blower assembly and took it outside. I got the motor replaced and also cleaned the clamshell assembly and the blower wheel with high pressure water and Blackhawk. I installed the motor into the assembly and installed the motor back into the system. I tested the fan and it is operating properly. I went outside and replaced the contactor. I made sure that all of the spades and screws were tight. I tested the system in cooling and the heat pump fired up right away. I collected the remaining balance for the repairs. System is in working order at completion of appointment.

I arrived and got straight to work. I removed the blower assembly and took it outside. I got the motor replaced and also cleaned the clamshell assembly and the blower wheel with high pressure water and Blackhawk. I installed the motor into the assembly and installed the motor back into the system. I tested the fan and it is operating properly. I went outside and replaced the contactor. I made sure that all of the spades and screws were tight. I tested the system in cooling and the heat pump fired up right away. I collected the remaining balance for the repairs. System is in working order at completion of appointment.

I arrived and got straight to work. I removed the blower assembly and took it outside. I got the motor replaced and also cleaned the clamshell assembly and the blower wheel with high pressure water and Blackhawk. I installed the motor into the assembly and installed the motor back into the system. I tested the fan and it is operating properly. I went outside and replaced the contactor. I made sure that all of the spades and screws were tight. I tested the system in cooling and the heat pump fired up right away. I collected the remaining balance for the repairs. System is in working order at completion of appointment.

I arrived and got straight to work. I removed the blower assembly and took it outside. I got the motor replaced and also cleaned the clamshell assembly and the blower wheel with high pressure water and Blackhawk. I installed the motor into the assembly and installed the motor back into the system. I tested the fan and it is operating properly. I went outside and replaced the contactor. I made sure that all of the spades and screws were tight. I tested the system in cooling and the heat pump fired up right away. I collected the remaining balance for the repairs. System is in working order at completion of appointment.