HVAC Service In Buda, TX

On arrival, I found the system completely flat on refrigerant (R-410A). Found the leak inside the line set located in slab of house. We have decided to move forward with replacement of the line set from the outdoor to indoor unit. Replaced the copper line set and thermostat wire running to the condenser. Put in new in line filter dryer, pressure tested with dry nitrogen and pulled a vacuum on the copper line set. Charged system to factory specs with new refrigerant.

Installed a 4-ton carrier 80% gas furnace and straight cooling condenser. Added new return and supply plenums and sealed pressures points with air lock. Rerouted gas line and rebuilt primary and secondary drain. Installed SS-2 and SS-3 safety switches and cleared drain line with compressed Co2. Installed line filter dryer and pressure tested system for extensive leak check. Pulled deep vacuum and weighed factory charge. Installed new outdoor disconnect and verified system operation. Everything working at this time.

Performed service diagnostic. Diagnostic found that the condensate drain line was clogged. Water had backed up into the safety switch. Options for repair were presented to the customer and they chose to have the drain line cleared. Drain line was cleared and flow tested with water. Drain line was treated. System was function checked and was running at the time of departure.

Performed diagnostic and found indoor system drain line clogged. Presented options to the homeowner and she agreed to drain service. Cleared and treated the drain line. Removed all water from pan. System operational upon completion of repairs.

Installed new Goodman straight electric system. Installed new plywood overlay. Rebuilt and insulated condensate drain line. Added SS2 safety float switch. Cleared and treated the drain and verified operation. Transitioned to supply plenum and sealed with mastic air lock. Sealed all buckets to the drywall with mastic. Pressure tested with dry nitrogen and pulled a vacuum on the copper line set. Replaced disconnect and whip. Verified system charge is to factory spec. System is working properly at time of departure.

Performed service diagnostic. Diagnostic found that the system was cutting off when calling for cooling. Low voltage short was popping the 3-amp fuse at the control board. A very fine cut was found in the low voltage wiring running to the condenser contactor. The cut was caused by the low voltage wiring running against the condenser unit where the refrigerant service ports are located. Options for repair were presented to the customer and they chose to have the wiring repaired. Wiring was repaired and then repositioned so that the wires are no longer rubbing against anything. System and air purifier were both checked and are operational. System was running at the time of departure.

Performed the AC tune-up. Cleared and treated the drain line. Condenser coil clean. No major issues were found.

Mr. Larry informed me the upstairs system was running and the outdoor system wasn’t coming on. I opened the cabinet up and found that the capacitor has failed. Replaced capacitor and system was function checked and is now operational.

Installed Carrier ductless system. Ran new copper line set and covered in line hide. Pressure tested and pulled a vacuum on the line set. Electricians ran power and mounted a disconnect near the unit. Verified system operation everything is operating at this time.

Performed service diagnostic. Diagnostic found that the condenser fan motor has failed. Options for repair were presented to the customer and they chose to have the condenser fan motor replaced today. Condenser fan motor was replaced and the system was function checked. System was running at the time of departure.

Performed semiannual maintenance on two cooling systems. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. Outside condenser refrigerant pressures are within range and condensers cleaned. Indoor system drain lines cleared and treated, and filters changed. No major issues were found and systems running at time of departure.

Performed semiannual maintenance on one cooling system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. Outside condenser refrigerant pressures are within range and condenser clean. Indoor system drain line cleared and treated. Filter recently changed by homeowner. I did notice that the outdoor capacitor is below value and the indoor blower wheel is dirty. No other major issues found. Presented my findings to the homeowners and they have decided to move forward with a new capacitor. Replaced capacitor and tested system. System is operational at this time.

Duct Replacement near Torrington St. Upon receiving a client's call, we promptly arrived at their home to assess the existing duct system. After identifying significant air leaks, poor insulation, and outdated design, we recommended a complete duct replacement. With the client's approval, we scheduled the services and returned to the residence to execute the replacement. Using top-quality materials and precise installation techniques, we installed a new ductwork system that maximized airflow, minimized energy loss, and enhanced overall comfort. The customer now enjoys improved energy efficiency, consistent temperatures, and optimal air distribution throughout their home.

A/C Replacement near Still Hollow Creek. A customer with an aging and inefficient AC system sought our expertise. After conducting a detailed assessment, we recommended an AC replacement to improve energy efficiency and performance. We installed a modern and energy-efficient American Standard air conditioning unit that met the customer's specific requirements. The new system delivered superior cooling, reduced energy consumption, and increased cost savings. The customer was delighted with the enhanced comfort and improved efficiency of their new AC system.

A/C Repair Service. Found the outdoor disconnect not completely passing power through. I installed a new outdoor disconnect and tested the system. I informed the homeowner she has a Federal Pacific Breaker Panel and needs to have a Licensed Electrician come inspect the panel. The system is an old R-22 unit. Did inform homeowner prior to leaving about the system and recommended replacement soon. Everything is working at this time.

Performed the AC tune-up. Cleared and treated drain line. Condenser coils clean. No major issues found.

Performed diagnostic. I found that the furnace had a faulty power switch. I replaced the switch and turned power back on, cycled the thermostat and system is now working at this time.

Performed service diagnostic. Diagnostic found that the capacitor on the condenser unit has failed. The terminal for the condenser fan motor was not allowing the condenser fan motor to reliably start. Without the condenser fan motor running the compressor was overheating and shutting down on a thermal lockout. Options for repair were presented to the customer and they chose to have the capacitor replaced. Condenser capacitor was replaced and the system was function checked. Electrical disconnect confirmed in and on. The system was running at the time of departure.

Performed service diagnostic. Diagnostic found that the condenser fan blade was contacting the conduit for the fan motor wiring. Fan blade was lowered to clear the conduit and the system was function checked. System was operational and was running at the time of departure.

Performed service diagnostic. Diagnostic found that the condensate drain line was clogged. Water had backed up into the secondary line and tripped the safety switch. Options for repair were presented to the customer and they chose to sign up for maintenance and to use this as their first maintenance visit. Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. No other major issues were found. Drain line cleared and treated. Condenser coil cleaned. Electrical disconnect confirmed in and on. System was running at the time of departure.