HVAC Service In Buda, TX

Performed semiannual maintenance on one straight electric cooling system. Inspected all Performance, Mechanical and Safety Systems. I did find the outdoor run capacitor to be below value, and the refrigerant charge is extremely low. Inspected the indoor unit and noticed the wrong size coil was installed during new construction; 4-ton evaporator case coil with a 5-ton condensing unit. I did recommend that we install the correct size coil and recharge the system back to factory specifications to ensure 100% cooling capacity of the HVAC system. I also completed a repair: The compressor high voltage wires were rubbing into the copper refrigerant lines. Secured wires to copper and placed down foam tape to prevent a future high voltage rub out.

Performed cooling maintenance. Checked electrical, mechanical and performance of the system. Cleared and treated drain line and washed condenser coil. No major issues were found. Disconnect is in and on. System is working at this time.

Performed cooling maintenance. Checked electrical, mechanical and performance of the system. Cleared and treated drain line and washed condenser coil. I replaced the 16x25x4 media filter. No major issues were found. Disconnect is in. System is on at this time.

Performed semiannual maintenance on one straight electric system. Inspected all Performance, Mechanical and Safety Systems. I did find the refrigerant change to be lower than normal for operation conditions. Drain cleared and homeowner changed filters prior to us arriving. System is an R-22 unit in fair condition.

Found the outdoor ECM exhaust motor on the main house system has failed, which was not allowing for the outdoor heat transfer. Will need to replace the outdoor motor to return system back to factory specifications for operation. Installed new outdoor condenser fan motor. Tested the cooling system to verify proper cooling operation. Everything is working at this time.

Performed semiannual maintenance on one cooling system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. Outdoor condenser refrigerant pressures are within range and condenser cleaned. Adjusted conduit to condenser. Indoor system drain line cleared and treated. Filter changed. No major issues were found. System running at time of departure.

Performed semiannual maintenance on one cooling system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. Outdoor condenser refrigerant pressures are within range and condenser cleaned. Indoor system filter changed and drain line treated. No major issues were found and system running at time of departure.

On arrival, I met with Mrs. Jones, and she stated that in her office shed located behind the garage the AC was not blowing as cold as it should. I turned the cooling system on and noticed the blower was not running like it should and noticed ice buildup on the expansion line. Checked the indoor washable filters and noticed they were extremely clogged up. Removed filters and noticed an immediate difference in how the system operated. Rinsed off the washable filters, inspected blower wheel and indoor fan coil, and verified they were operating within manufacture’s specifications for operation. Homeowners have sold the house and just needed to get the mini split working before moving out. Everything is working at this time.

Performed semiannual maintenance on one cooling system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. Outside refrigerant pressures are within range. Indoor system drain line cleared and filter changed. No major issues were found. System running at time of departure.

Completed duct work. Removed old flex and triangles. Replaced triangles with metal wyes. Replaced supply plenum and sealed with mastic airlock. Rehung new flew and installed balancing dampers at each takeoff. System operating at this time

Ductwork Replacement near Cold Spring. Arrived at the client's home to replace the old ductwork with a more energy-efficient option. Removed the old ducting from the home and installed and sealed the new ducting for the customer.

HVAC Repair near Bluff St. Contacted for HVAC repairs and arrived at the client's home to look into the issues. Discovered the issues were derived from the compressor on the HVAC unit. Replaced the compressor on the system to restore operation for the grateful customer.

Ductwork Replacement Services near Bradfield Dr. Called to replace the ductwork in a residential client's home. Arrived and removed the old ductwork from the home. Installed new and improved ductwork throughout the client's home to provide a more energy-efficient alternative to their previous ductwork.

HVAC Service near Garlic Creek Dr. Called out to service a residential client's HVAC unit. Thoroughly inspected the unit and discovered the system's failure to be due to a misaligned blower wheel. I removed the blower assembly and replaced the damaged blower wheel to restore function to the HVAC unit.

Performed semi annual maintenance on one cooling system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufactures specifications for operation. Outside condenser refrigerant pressures within range. Condenser was washed off. Inside drain line clog was cleared. No other issues were found. System running at time of departure.

Performed semi annual maintenance on one cooling system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufactures specifications for operation. Outdoor condenser refrigerant pressures. Within range and condenser cleaned. Inside system drain line cleared and filter changed.

Installed new ducting system. Added new I-boxes, sheet metal elbows and wyes, and dampers. Sealed all pressure points with air lock and hung flex duct. System operating at this time.

Performed semiannual maintenance on one straight electric cooling system. Inspected all Performance, Mechanical and Safety Systems. Did find the outdoor compressor wires were very tight and rubbing up against the copper. Placed down some foam tape and secured the wires with wire ties to help eliminate the possibility of a high voltage rubout. Did also wash down the exterior coils as the rear side of coil had lots of grass clippings against the coil. Verified everything was working within manufacture’s specifications for operation.

Performed semiannual maintenance on one cooling system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. Outdoor condenser refrigerant pressures are within range and condenser cleaned. Indoor system drain line cleared and filters changed. No major issues were found.

Installed New Carrier Heat Pump. Installed new liquid line filter drier. Pressure tested with nitrogen and pulled a vacuum on the copper line set. Rebuilt drain line and Installed SS2 Safety float switch. Installed new plywood overlay. Installed New Breaker box in closet. Replaced Supply Plenum. Removed old ductwork and installed new trunk link.