HVAC Service In Buda, TX

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. I did find that the compressor was pulling excessive amps on startup. No other issues were found. The system was running at the completion of service.

Performed AC cool check on two systems. Checked the electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain lines and flow tested the drains with two gallons of water. I also treated the drain lines. The air filters were replaced by the homeowner before my arrival. No major issues were found. The systems were running at the completion of service.

Removed all existing ductwork from the system. Installed new flex duct, buckets and supply registers. Upsized where needed. Used sheet metal wyes where needed. Built and installed new return plenum and extended supply plenum. Sealed all ductwork connections with mastic/hardcast. Tested operation of system. Everything is working at completion of ductwork installation.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was clean and had been recently replaced by the homeowner. No major issues were found.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was clean and had been replaced before my arrival. The condenser fan motor showed signs of overheating. No other issues were found. The system was running at the completion of service.

Heating tune-up completed on a vertical furnace. Drain line was flushed and treated. Flame sensor was cleaned. All mechanical and electrical components were checked. I did find the torque booster for the blower motor well below manufacturers specifications. I also found severe discoloration throughout the furnace control board and biological growth on the evaporator coil reaching to the supply plenum. I went over my findings with the homeowner.

On arrival, I spoke with the homeowner and he informed me the outdoor system was not turning on. He had a company out to fix his foundation recently and they left the breaker off for the unit. I reset the breaker and function tested the system. I then performed an a/c tune-up on the Carrier straight cool system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I adjusted the airflow for the 3 ton system and lowered the static pressure from .8 to .65 in. w.c. I also found the outdoor condenser breaker is oversized and the outdoor disconnect is getting difficult to pull off. No other issues were found. The system is running at completion of service.

After diagnosing the system, I found that the main issue was a clogged primary drain line. I did speak with the homeowner about multiple options for repair. She chose to sign up for our gold membership plan and have her primary drain line cleared, flushed, treated and primed. After work was completed, I function tested the system to verify proper operation. Everything is working at completion of service

Performed heater tune-ups on two propane Carrier furnace systems. Checked the electrical, mechanical and performance systems of the units. Cleared, cleaned, flushed and treated the drain lines and cleaned the exterior of the furnace systems. The master bedroom system is showing wear and tear due to the age of the system. The heat exchanger has some stress marks. The indoor coil is rusted and could have a refrigerant leak in the future. The blower capacitor is slightly low but still within range for operation. Spoke with the homeowner about my findings and he is going to keep an eye on the system. No other major issues were found. Both systems are operational at this time.

Performed heater tune-up on two Lennox propane furnace systems. Checked the electrical, mechanical and performance systems of the units. Cleared, cleaned, flushed and treated the drain lines and cleaned the exterior of the furnace systems. Homeowner was concerned about two supply registers in her master bedroom that had biological growth. I washed both registers at no additional cost. I informed her this was most likely happening due to the hot steam from the shower mixing with the cold air from the duct. No other issues were found. Both systems are operational at this time.

Service diagnostic found that the condensation drain line was clogged. Water had backed up into the safety switch and shut down the condenser unit. I also found biological growth inside the air handler. I removed the safety switch from the drain line and tested the system. The system was running and cooling at 8-8.8 degrees of sub cooling. Options for repair were presented to the homeowner and they chose to have the drain line cleared. I cleared the drain line and flow tested the drain with water. I also treated the drain line. I the function tested the system and the system was operational. The system was running at the completion of service.

Heating tune-up completed on a horizontal furnace. Flame sensor was cleaned. Drain line was flushed and treated. All electrical and mechanical components were found within manufacturer specifications. The furnace is heating properly at time of departure.

Heat check completed on a horizontal heat pump. Outdoor coils were cleaned. Drain line was flushed and treated. I did find lubricant leaking from the outdoor fan motor. I also found in rush amps to the compressor exceeding limitations from manufacturer. I went over my findings and repair options with the homeowner. The system was running at completion of service.

Replaced entire flue pipe run with new 4” pipe running up and out the roof. Added flashing, rain ring and top cap as well as secured with strap and zip screws. Replaced gas valve and ran new black pipe out of the furnace with drip leg. Added foam blocks support under the evaporator coil and sealed torn duct with exposed insulation. Verified system operation in heating. Everything is working at this time.

Performed heater tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Secured outdoor compressor wiring and washed the outdoor coil. Filters were replaced recently and are clean. No major issues were found. The system is operational at this time.

Heating tune-up completed on a vertical heat pump system. Outdoor coils were clean. Drain line was flushed and treated. During maintenance all mechanical and electrical components were checked. The system is heating properly at time of departure.

Heat check completed on a horizontal gas system. Drain line was flushed and treated. Flame sensor was cleaned. All mechanical and electrical components found within manufacturer specifications. The system is heating properly at time of departure.

Heating tune-up completed on a horizontal furnace. Drain line was flushed and treated. Flame sensor was cleaned. All mechanical and electrical components were found within manufacturer specifications. Before leaving, the thermostats were reset to homeowners preferences. Everything is running at completion of service.

Heat check completed on a vertical gas system. Drain line was flushed and treated. Flame sensor was cleaned. All mechanical and electrical components were found within manufacturers specifications. The system is heating properly at this time.