Kyle TX Heating & Air Conditioning Services

During our evaluation we discovered that there is mold growth starting to form inside the system. We also found that the system outside was overcharged with refrigerant. We removed a bit of refrigerant to get the system down to 11 degrees of sub cool per the manufacturers label. We also cleaned the growth and showed it to the homeowner before we did so. System is in working order at completion of appointment. See attached checklist for full tune-up details.

Installed Carrier 4-ton furnace. Installed Ecobee Pro thermostat. Installed new extended supply plenum. Installed return air plenum and sealed all connections with mastic. Replaced secondary drain pan. Rebuilt and insulated condensate drain line. Cleared and verified drain operation. Installed SS2 and SS3 safety float switches. Replaced disconnect and whip at the outdoor unit. Replaced condenser pad. Pressure tested and pulled a vacuum on the line set. Charged system to manufacturers specs. Completed dryer vent cleaning.

Installed 3.5-ton Carrier heat pump system. Installed new extended supply plenum and new return plenum. Installed Ecobee Pro and paired the sensor to it. Installed new secondary drain pan. Rebuilt and insulated condensate drain line. Installed new junction box. Cleared and treated drain as well as verified operation. Installed new disconnect and whip for outdoor unit and ran the low voltage in the same whip. Pressure tested and pulled a vacuum on the line set. Verified system charge was to manufacturer’s specs.

Performed cooling maintenance on one straight cool system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. Customer supplied filters for replacement. No major issues were found. System is operational at this time. See attached checklist for full tune-up details.

Performed cooling maintenance on one straight cool system. Checked electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I found the outlet of the primary drain line outside was draining too close to the house. I added some more length to the drain line to prevent damage to the foundation overtime. No other major issues found. See attached checklist for full tune-up details.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. Cleared and treated the drain line. The blower motor capacitor is below value. The blower wheel is clean. Control wiring was tightened. The heat exchangers are rusted. Options for repair were presented to the homeowner. He chose to have the blower motor capacitor replaced today. I also spoke to him about the condition of his heat exchangers and what that means for the life of the furnace and the safety of the home. The blower motor capacitor was replaced. The system was function checked and was running at the time of departure.

Service diagnostic found that the condensate drain line was clogged. Water had backup up into the secondary line and tripped the safety switch. I cleared the drain and flow tested the drain with water. I then treated the drain. Performed the AC cool check. No other major issues were found. The system was set to the customer’s desired temperature and was running at the time of departure. See attached checklist for full tune-up details.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. Return and supply ducts are clean. The blower wheel is also clean. Electrical wiring is tight. Blower motor capacitor is within value. Condenser coil clean. Condenser capacitor is within value. The condenser fan motor is in good condition. Condenser wiring is tight. The contactor is also in good condition. No major issues were found. See attached checklist for full tune-up details.

Performed AC cool check on a Carrier heat pump and a Carrier mini split system. Checked electrical, mechanical, safety, and performance of the systems. Return and supply ducts are clean. The air handler, evaporator coil and blower wheel are also clean. Electrical wiring is tight and in good condition. I cleared the drain and flow tested it with water. I also treated the drain. The filter was replaced with a customer supplied filter. Condenser fan motor is in good condition as well as the contactor. The capacitor for the condenser unit is within value. I treated the electrical with JS insecticide. Condenser coil was cleaned. The mini split is in excellent condition. The blower wheel is clean and oscillating. I cleaned the filter today. The evaporator coil is clean. Electrical wiring is tight. I cleaned the condenser as well. The system was running, and water was freely draining from the system. No major issues were found with either system. Both systems were running at th

Service diagnostic found that the fuse on the furnace control board was blown. I went through the wiring and found the short was in the Y wire running to the condenser unit due to a bad contactor. Every time the system was calling for cooling the short would pop the fuse and prevent system operation. Options for repair were presented to the homeowner and he chose to have the contactor replaced. I replaced the contactor and the blown fuse. I then function checked the system. The system was running and cooling. System was running at the time of departure.

Springtime Air Conditioning Tune-Up: During a thorough spring AC tune-up, I meticulously inspected the refrigerant line for leaks. In addition to this, I cleaned the evaporator coil, inspected and straightened coil fins, cleared condensate drains, and verified and tightened all electrical connections. This attention to detail guarantees leak-free refrigerant circulation, optimal heat exchange efficiency, smooth drainage, unobstructed airflow, and secure electrical components, contributing to the AC system's peak performance.

Air Conditioning Repairs: Investigating the cause of the client’s AC system failures. Addressed uneven cooling by balancing refrigerant levels. Optimized the distribution of refrigerant to achieve uniform temperature throughout the space.

Air Purification System Installation: In response to a homeowner's air quality concerns, I installed a cutting-edge Duct Air Purifier. Seamlessly integrated into the existing HVAC system, it effectively eliminates contaminants, ensuring a consistently clean and healthy indoor environment.

AC Repairs: Arrived for a service call on a client’s inoperable AC system. Identified a faulty compressor causing inadequate cooling. Replaced the compressor to restore proper refrigerant circulation and overall system functionality.

Performed cooling maintenance. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I found multiple deficiencies with the system. I informed the customer, and he chose to have both indoor and outdoor capacitors replaced, have a blower wheel cleaning performed, and have the outdoor condenser fan motor replaced. After I completed the repairs, I cycled power at the thermostat and confirmed the system was operational. No other major issues were found, and system is on and running at this time. Please see attached checklist for full tune-up details.