Kyle TX Heating & Air Conditioning Services

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. Air filter was replaced with a client supplied filter. I cleaned the condenser coil. No major issues were found. The system was running at the completion of service.

On arrival I found that the 24v fuse inside the air handler had blown. I checked through the system and found that the contactor in the condenser unit had failed and was shorting the Y wire. I also found that the capacitor for the condenser unit was below value and that the condenser fan motor showed signs of overheating. I presented repair options to the homeowner and Robert chose to replace the contactor and capacitor in the condenser unit. I replaced the contactor and capacitor in the condenser unit, then performed a system maintenance. Drain line was cleared and flow tested with water. I also treated the drain line. Air filter was clean and had been recently replaced. No other issues were found. The system was running at the completion of service.

Performed heater tune-up on a Carrier Infinity straight cool system and checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Cleaned the exterior of the furnace and washed the outdoor coil. The system is operational at this time.

Performed A/C tune-up on a York straight cool system and checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Cleaned the exterior of the furnace and washed the outdoor coil. I found the outdoor condenser fan motor and compressor showing signs of over heating. No other issues were found. System is operational at this time.

Performed A/C tune-up on a Rheem straight cool system and checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Cleaned the exterior of the furnace and washed the outdoor coil. No major issues were found. Both surge protection devices are working. The system is operational at this time.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was clean and had been recently replaced by the homeowner. I cleaned the condenser coil. The condenser fan motor showed signs of overheating. No other major issues were found. The system was running at the completion of service.

Performed diagnostic on the system. I found that the nest thermostat was not sending a 24 volt signal to the O wire for the reversing valve and was running in heat mode. I also found the outdoor starter is pitted at the contacts. I spoke with the homeowner and he decided to have the starter replaced, install two surge protectors and perform an A/C tune up. I replaced the starter. Installed both surge protectors, one for the indoor system and another one for the outdoor system. I also replaced the nest thermostat with the old Honeywell thermostat that the homeowner provided at no additional cost. I then performed an A/C tune-up on a Lennox heat pump system and checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and washed the outdoor coil. The system is now operational.

Performed A/C tune-up on a Carrier straight cool system and checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Cleaned the exterior of the furnace and washed the outdoor coil. No major issues were found. All UV lights and surge protectors are working. The system is operational at this time.

Installed 4 ton Carrier R-454B condenser and evaporator coil. Moved new condenser to be 6 feet from the gas meter. Installed vertical Carrier gas furnace with new flue pipe connections and new gas connections. Installed new supply plenum. Sealed all connections with mastic / hardcast. Installed Ecobee pro thermostat with new thermostat wires, relocated to upstairs. Installed new plywood overlay for the furnace to sit on. Pressure tested system with nitrogen and pulled vacuum. Rebuilt primary condensation drain with new safety switch. Cleared primary condensation drain and primed p-trap with water. Charged system with R-454B refrigerant. Tested heating and cooling operation. Everything is working at this time.

AC cooling maintenance completed on six year-old Carrier straight cool system. Drain line flushed cleared and treated. Static pressure checked. All electrical and mechanical within manufacturer specs. No major issues found. The system is cooling properly at this time.

AC cooling check completed on four year-old upflow straight cool Carrier system. All electrical and mechanical components are within manufacturer specifications. No major issues found. The system is cooling properly at time of departure.

Performed A/C tune-up on a Carrier straight cool system and checked the electrical, mechanical and performance systems of the unit. I replaced the high voltage wire nuts with a Wago wire connector. Adjusted the airflow and the system is now delivering 910 cfm on a 2.5 ton system. Homeowners decided to buy a Honeywell media filter and I replaced it for them as well. Cleared, cleaned, flushed and treated the drain line. I cleaned the exterior of the furnace and washed the outdoor coil. The system did have a 17 degree temperature split and it is cooling. No major issues were found. The system is operational at this time.

Performed semiannual maintenance on one heat pump cooling system and inspected all performance, mechanical and safety systems. Cleaned out the outdoor unit and washed condensing coils to ensure proper heat transfer of the refrigerant, flushed and treated the primary drain lines. I found the outdoor service disconnect for the heat pump to have melted connections at the line side high voltage. I presented my findings to the homeowner and they chose to replace the disconnect today. I installed the new outdoor high voltage disconnect, tightened and secured electrical lugs to 45in-lbs, installed new high voltage electrical whip for disconnect to heat pump and secured at condenser. Sealed the disconnect box to the wall to help prevent any insects or weather elements from getting behind it into the exterior wall. Everything is working at this time.

Change coil, replace filter dryer, pressure test to 200, vacuum down to 100, bubble check braze spots, check water drain and pan, clear drain, add 3lbs Of refrigerant, Put drain and b-vent back In place, tested unit in cooling and heat as well as zone dampers. Unit is operational and running.

Installed new condenser fan motor. Installed new contactor for the condenser. Installed new secondary drain pan and added SS2 / SS3 safety switches. Cleared primary condensation drain and primed p-trap with water. Tested heating and cooling operation. Everything is working at this time.