San Marcos TX Heating & Air Conditioning Services

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. Condenser fan motor showed signs of overheating. System was low on refrigerant. Condensate drain line was poorly piped into a bathroom sink. None of the ductwork had any sealant on the connections or buckets for the registers. Flue pipe has a downward slope where the pipe runs toward the roof penetration. Options for repair were presented to customer and they chose to replace the condenser fan motor, charge the system with refrigerant and install surge protection. Repairs completed, electrical disconnect confirmed in and on. System was running at the time of departure. Please see attached checklist for full tune-up details.

Performed AC cool check on two systems. Checked electrical, mechanical, safety, and performance of the systems. No major issues were found. Drain lines cleared and treated. Condenser coils cleaned. Electrical disconnect confirmed in and on. Systems were running at the time of departure.

Diagnosed that the blower motor is rotating out of position causing a noise. Due to this, it will fail soon. Gave the client her options and she chose to have the motor replaced. I replaced the blower motor on the indoor head unit and completed a complimentary cleaning of the blower wheel. I checked temperature split to confirm operation and system had 20-degree split. System fully operational.

Inspected all Performance, Mechanical and Safety Systems. Found the outdoor run capacitor has failed not allowing for the compressor to pump refrigerant throughout the indoor cooling coils. Repaired outdoor system and checked all systems. Verified everything was operating within manufacture’s specifications for operation.

Installed new 3-ton Carrier heat pump system in closet. Sealed ductwork connections and gaps in the insulation. Added new indoor serviceable disconnect and capped off unused power leg. Removed poor duct board plenum and installed new partial supply plenum. Sealed with air lock and mastic tape. Rebuilt drain line with SS-2 safety switch and new stack vent on trap. Sealed return chase with insulation and added 2x4 brace. Installed new line filter dryer and pressure tested system for extensive leak check. Pulled deep vacuum and weighed in factory charge. Also replaced return and supply registers.

Performed the AC tune-up. While performing the inspection I did find deficiencies with the system. I presented the clients with their options, and they chose to have the mandatory repairs done at this time. After performing the repairs everything is working at this time.

Installed new Payne gas system in attic. Added new vibration isolators and drain pan. Rebuilt drain line with SS-2 and SS-3 safety switches. Added line filter dryer and pressure tested system for extensive leak check. Pulled deep vacuum and weighed in factory charge. Re-piped gas line with sediment trap and reused the thermostat. Installed new return plenum and reused supply plenum. System operating at this time.

Performed the AC tune up. While performing the inspection I did find that the battery cap to the blower motor was failing. I presented the client with her options, and she chose to have it replaced at this time. I also found that the Stage 4 Breathe Easy was not working so I replaced it under the parts and labor warranty at this time. After performing these repairs everything is working at this time.

Performed the mandatory repairs. Installed Stage 3 Breathe Easy package into the air handler to combat the mold growth inside. Also performed ductwork sealing on the flex duct at the plenum as well as the I-boxes to the sheetrock.

After performing the diagnostic, I found that the evaporator coil has a major leak in it. I presented the client with her options, and she chose to have it replaced. Installed new cased coil in attic. Added new line filter dryer and pressure tested system for extensive leak check. Pulled deep vacuum and weighed in new factory charge with R410-A. Rebuilt drain line with SS-2 and SS-3 safety switches. Cleared drain line and verified system operation.

After performing the diagnostic, I found that the fuse was blown inside the air handler. I did find loose low voltage connections as well. I presented the client with his options, and he chose to have both repaired at this time.

Performed service diagnostic. Diagnostic found that the blower motor had failed. Options for repair were presented to customer and they chose to have the motor replaced today. Repair was completed. Electrical disconnect confirmed in and on system was running at the time of departure.

Performed maintenance on the AC system. Checked all electrical and mechanical systems. Cleared drain and cleaned condenser. The client had cleaned off the biological growth that was mentioned at the last visit.

Performed service diagnostic. Diagnostic found that the contactor on the condenser unit had failed and was not passing power. Options for repair were presented to the customer and they chose to have the contactor replaced today. Repair was completed. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed service diagnostic. Diagnostic found that the primary condensate drain had clogged and tripped the safety switch. Options for repair were presented to customer and they chose to have the drain cleared and treated. Repair was completed. System was running at the time of departure.

Diagnosed failed outdoor capacitor. Replaced capacitor and system is now operational.

Trip 1 - After performing the diagnostic, I found that the communicating blower motor had completely failed. I presented the client with his options, and he chose to have it overnighted so they can have cool air for the weekend. I will be returning tomorrow to install the new blower motor. Trip 2 - Performed the repairs on the blower motor. After getting the system back up and running, I performed the AC tune-up. I did find other deficiencies with the system however the client informed me that he is going to hold off and let us know on our next visit what he would like to do since he just made a big repair. Everything is working at this time.

Installed new Carrier 3.5-ton gas system. Replaced supply and return plenum and one distribution box. Replaced the zoning dampers and added a static bypass damper. Replaced the zone control board. Rebuilt condensate drain line and insulated it. Installed new SS-2 and SS-3 safety float switches. Rebuilt gas line to system. Replaced inline filter dryer, pressure tested with dry nitrogen, and pulled a vacuum on copper line set. Added attic insulation tent.

After performing the diagnostic, I found that the battery cap had completely failed and the starter was failing. I presented the client with her options, and she chose to have them replaced and sign up for our Gold maintenance plan. Repairs completed and AC tune-up performed. While performing the AC tune-up I found mold inside the air handler. I presented the client with options to install our Stage 3 and Stage 4 Breathe Easy packages and she accepted. Installed both Breathe Easy packages and tested everything. System operational.

Performed the AC tune-up. While performing the inspection I did find that the battery cap to the blower motor was failing. I presented the client with his options, and he chose to have it replaced at this time. I also found the system to be slightly low on refrigerant. I added half a pound of R-410A refrigerant to the system and signed the client up on our Gold maintenance plan so we can monitor it on our next visit out here.