San Marcos TX Heating & Air Conditioning Services

Performed the AC tune-up. While performing the inspection I did find deficiencies with the system. I presented the client with his options, and he declined all repairs.

Performed the AC tune-up. While performing the inspection I did find deficiencies with the system. I presented the client with her options, and she would like to think it over and will contact us when ready to move forward with repairs.

Installed new evaporator coil on horizontal system along with a new filter dryer. Connected the new coil to existing line set and performed a pressure test on the system. Then performed evacuation to remove atmosphere from system and finally charged and tested the system. We brought system pressures up to factory specifications. System was tested along with the drains to confirm operation. No issues were found, and system is operational at this time

Performed maintenance on the AC system. Checked blower and evaporator coil. Cleared drain and also sprayed with drain cleaner. Condensing coil had build-up on it so I cleaned it before checking pressures; pressures found to be in range. No major issues found.

After performing the diagnostic, I found that the primary drain line was completely clogged and tripping the safety float switch. I presented the client with his options, and he chose to have it cleared at this time. I did find other deficiencies with the system and presented them to the client, but they chose to wait on further repairs. System operational upon completion of drain treatment.

Performed the AC tune-up and everything is working at this time.

After performing the diagnostic, I found that the fan relay and blower motor battery cap had completely failed. I presented the client with his options, and he chose to have the relay and battery cap replaced. After performing the repairs everything is coming on and working at this time.

Diagnosed a short in the low voltage wiring to the condenser. Gave her options and she chose to replace the wire. Re-ran thermostat wire from penetration of crawl space to the condenser. Also added new Armaflex on suction line and secured disconnect to wall. Tested system and it is operational.

Installed new Rheem heat pump system in closet. Rebuilt platform and reinforced frame. Replaced RAFGs and sealed all pressure points. Installed new line filter dryer and pressure tested system for extensive leak check. Pulled deep vacuum and verified system operation. Rebuilt drain line with SS-2 safety switch.

After performing the diagnostic, I found that the primary drain line was completely clogged and tripping the safety float switch. I presented the clients with their options, and they chose to have it cleared today. After clearing the drain line and pumping the secondary drain pan everything is coming on and working at this time.

After performing the diagnostic, I found that the primary drain line was backed up and tripping the safety float switch. I presented the client with her options, and she chose to have the drain line cleared and treated. After performing the repair everything is coming on and working at this time.

Performed the AC tune-up and everything is working at this time. I had a temperature split from return to supply of 27 degrees.

After performing the diagnostic, I found that the battery cap and starter had failed. I presented the client with her options, and she chose to have the repairs done at this time. After performing the repair, the system is coming on and working at this time.

Performed the AC tune-up and everything is working at this time.

Performed service diagnostic. Diagnostic found that the capacitor on the condenser unit had failed. Mold was also found in the air handler around the evaporator coil. Options for repair were presented to customer and they chose to replace the capacitor. Repair was completed. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. Capacitor for the condenser unit was below value. No other major issues were found. Drain line cleared and treated. Condenser coil cleaned. Options for repair were presented to customer and they chose to replace the capacitor. Repair was completed. Electrical disconnect confirmed in and on. System was running at the time of departure.

After performing the diagnostic, I found that the blower motor had completely failed. Installed the new blower motor and everything is coming on and working at this time. Checked the refrigerant pressures and they are okay however it is 85 degrees inside the house so it will take a few hours to cool off the home. I have a 20-degree split from the return to the supply output.

Replaced both return plenums and installed new 20x25 media filters. Replaced the supply on the upstairs system and installed reducers that go from 16 to 10 inch on the end of the plenum. We also raised the furnaces with foam blocks to align with the top of the coils to allow better airflow across the coil. Each joint was sealed with airlock and mastic sealant. Both systems are working properly at time of departure.

Performed the AC tune-up and everything is working at this time. While performing the inspection I did notice that when the roof was replaced, they pushed the flue pipe down about 8". I informed the client, and she chose to have me re-adjust the flue pipe so that it is at an upward draft all the way out of the house. I did also talk to the client about surge protection, and she wants to wait until our next visit.

After performing the diagnostic, I found that the primary drain line was backed up and bypassing the secondary drain pan. I presented the client with his options, and he chose to have the drain line cleared and treated at this time. I did discuss the other deficiencies with the system, and also discussed the maintenance plan, however he declined because he is selling the house in the next month. I performed the drain treatment and system was operational. While I was collecting payment, I heard the condenser cycle on and off multiple times. I performed further diagnostics and found that the zone control board on the indoor unit was failing. The client chose to have that replaced as well at this time. I replaced the board and tested the system.