Wimberley TX Heating & Air Conditioning Services

Performed semiannual maintenance on one straight electric heating system. Inspected all Performance, Mechanical and Safety Systems. Flushed and treated the drain line and pan. Removed filter grille cover and removed as much dirt and dust from the louvres as possible. Verified everything was operating within manufacture’s specifications for operation. Surge protection devices are green lit and operating as designed at time of visit.

Performed semiannual heat pump maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. All Stage 3 Breathe Easy lights are on and operational during the time of visit.

Trip 1 - Performed service diagnostic. Diagnostic found that the igniter on the furnace had broken. Options for repair were presented to customer and they chose to have the igniter replaced. Will order OEM igniter from the supply house on Monday and will contact customer to schedule once part is received. Trip 2- Repair was completed. System was function checked. System was running at the time of departure.

Performed semiannual maintenance heating maintenance. Inspected all Performance, Mechanical and Safety Systems. Found the firmware needed to be updated which fixed the heating issues. Everything is working at this time.

Performed semiannual maintenance on one heat pump heating system and one mini split. Inspected all Performance, Mechanical and Safety Systems. On the heat pump system, I did find the outdoor exhaust fan motor to be overheated and showing signs of wear. Also noted the indoor fan coil is rusted and corroded. Used my electronic leak detector and tested coil for refrigerant leaks. Did not locate any at this time, but the coil does need to be monitored moving forward for refrigerant leakage.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. All surge protection devices are on and functioning per design.

Performed heating maintenance. Checked electrical, mechanical, safety, and performance of the system. No major issues were found. Drain line cleared and treated. Condenser coil clean. Electrical disconnect confirmed in and on. System was running at the time of departure. Please see attached checklist for full tune-up details.

Performed heating maintenance. Checked electrical, mechanical, safety, and performance of the system. Reme-Halo is operational. No major issues were found. Drain line cleared and treated. Condenser coil cleaned. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Condenser fan motor is leaking grease. Mold/mildew was found inside the air handler. No other major issues were found. Drain line cleared and treated. Condenser coil cleaned. Options for repair were presented to customer and they chose to have the condenser fan motor replaced and to have system sterilizers installed today. Repairs were completed. Electrical disconnect confirmed in and on. System was running at the time of departure.

Found thermostat failed to allow for heating operation. Installed new Honeywell thermostat and tested all operations. Everything is working at this time.

Performed semiannual maintenance on 4 heating systems. Inspected all Performance, Mechanical and Safety Systems. I did find, in the heat pump heating system, that the condenser exhaust motor has overheated and is showing signs of wear and tear. Also noted, on the upstairs main house furnace, that the gas line is not properly ran into the furnace. All systems are working at this time.

Trip 1 - Inspected the indoor heat kit and found all heating relays had failed. It will not convert VAC to VDC which is preventing the contacts from closing. Also found the outdoor heat pump defrost board has failed not allowing for complete changeover of the reversing valve. Inspected the back of the board and found burn marks on circuit paths. I recommended replacing both components as well as a new thermostat as it has failed after a power surge. Lastly, I recommended installing surge protection devices on both the indoor air handler and the outdoor heat pump. The homeowner has decided to move forward with replacement of the board and heat kit. Our office will reach out to schedule once parts have arrived. Trip 2 - Replaced the heat kit in the air handler. Replaced the defrost control board and the thermostat for it. Both the heat kit and condenser are working properly at this time.

Performed service diagnostic. Diagnostic found that the capacitor on the condenser unit had failed. Options for repair were presented to customer and they chose to have the capacitor replaced today. Repair was completed. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Capacitor on the condenser unit was below value. No other major issues were found. Drain line cleared and treated. Condenser coil cleaned. Options for repair were presented to customer and they chose to have the capacitor replaced today. Repair was completed. Electrical disconnect confirmed in and on. System was running at the time of departure. Please see attached checklist for full tune-up details.

Performed service diagnostic. Diagnostic found that the primary condensate drain line was clogged. Water had backed up into the secondary drain line and tripped the safety switch. Options for repair were presented to the customer and those chose to have the drain cleared and treated. Drain line was cleared, flow tested with water and treated. System was running at the time of departure.

Customer decided to go ahead and have new breaker installed as well. Installed new breaker on outdoor panel. Replaced indoor heat kit and verified system operation. System operating at this time.

Tested all Performance, Mechanical and Safety Systems. Found the outdoor starter to have failed not allowing for high voltage electricity to pass through and turn on outdoor unit components. Recommend replacement of the outdoor contactor to return system back to operation. Homeowner agreed. Completed repair and system is now operational.

Replaced evaporator coil. Rebuilt drain and hooked float switch back in. Charged system to factory specs. Tested operation of system and is working properly upon departure.

Installed new 3-ton Carrier gas system. Installed new Ecobee Pro thermostat. Rebuilt and insulated condensate drain line. Replaced secondary drain pan. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Replaced both the supply and return plenum and sealed with mastic airlock. Added an Aprilaire 210 media filter to return. Charged system to factory spec. System is working properly at time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. Primary condensate drain line was clogged. Drain line was cleared and flow tested with water. Drain line was also treated. No other major issues were found. Condenser coil was cleaned. Electrical disconnect confirmed in and on. System set to 77 degrees per customer. System was running at the time of departure.