HVAC Service In Buda, TX

Performed heater tune-up on a Carrier gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I did find the main breaker for the outdoor system is oversized. The current breaker is a 30A two pole Cutler Hammer and the system needs a maximum 25 amp breaker. Presented repair options to the customer. No other major issues were found. The system is running at completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. No major issues were found. The system was running at the completion of service.

Installed 4 Ton Carrier 2 stage R-454B heat pump system. Air handler in attic with heat kit 15kw. Installed Ecobee pro thermostat. Installed new secondary drain pan. Built and installed new supply and return plenums. Built and installed new return box above filter grill. Installed new 16 inch return flex duct. Upsized duct to bedroom from 6 to 8 inch flex. Rebuilt primary condensation drain, added SS2 and SS3 safety switches. Primed trap with water. Sealed all ductwork connections with mastic / hardcast. Weighed in 1lb 14oz R-454B refrigerant. Tested heating and cooling operation of new system. Everything is working at completion of install.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters were replaced with client supplied filters. No major issues were found. The system was running at the completion of service.

Heat check completed on a vertical gas system. Drain line was flushed and treated. Flame sensor was cleaned. All mechanical and electrical components checked. I did adjust the gas pressures to spec for liquid propane. No major issues were found. The system is heating properly at time of departure.

Performed heater tune-up on an American Standard and Carrier Heat Pump systems. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain lines and cleaned the exterior of the air handlers. Verified outdoor compressor wiring is secure and washed both outdoor coils. No major issues were found. Both systems are operational at this time. I did leave both thermostats off per homeowner request.

Performed heat check on two systems. I cleared the condensation drain lines and flow tested the drains with two gallons of water. I also treated the drain lines. The air filters were clean and had been recently replaced by the homeowner. No major issues were found. Both systems were running at the completion of service.

Performed heater tune-up on a Carrier Infinity Heat Pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Secured the outdoor compressor wiring and washed the outdoor coil. No major issues were found. The system is operational.

Recovered old refrigerant and removed the indoor coil. Installed new coil and filter drier. Pressure tested system and pulled a vacuum. Weighed in new refrigerant and additional refrigerant to account for the lineset length. Installed new outdoor fan motor. Cleared drain and verified operation of system and drain. Got temp split in heating. Everything is working at completion of service.

Heating tune-up completed on a vertical heat pump system. Drain line was flushed and treated. Heat pump coils were cleaned. All mechanical and electrical components checked and found within manufacturer specifications. No major issues were found. The system is heating properly at this time.

Heat check completed on one vertical heat pump. Drain line was cleared and treated. Condenser coils were cleaned. All mechanical and electrical components were checked. I did find the outdoor contactor charred and pitted. I went over my findings with the homeowner and he chose to replace the contactor. Once repairs were completed the system was cycled on to verify proper operation. No other major issues were found. The system is heating properly at this time.

Performed heater tune-up on a Lennox zoned gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I did find the system is running at high static but due to the location of the system there is no room for improvements. No other issues were found. The system is operational at this time.

Performed heater tune-up on a Carrier gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. Outdoor surge protection device is working. I did find there is no surge protection device on the indoor system. The Synergy air purifier has also failed. No other issues were found. The system is operational.

Removed remaining refrigerant and replaced indoor coil. Releveled the system and flared all connections. Pressure tested and pulled a vacuum. Weighed in all new refrigerant in the system. Everything is working at completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed heater tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Verified outdoor compressor wiring is secured and washed the outdoor coil. I did find the outdoor starter is pitted at the contacts. I removed the schedule setting on the thermostat per homeowner request. No other issues were found. The system is operational.

Heat check completed on a horizontal heat pump system. Condenser coils were cleaned. Drain line was flushed and treated. All mechanical and electrical components were checked. I did find the condenser fan motor leaking lubricant and the torque booster below manufacturer specifications. I presented my findings and repair options to the homeowner and she chose to replace both the condenser fan motor and outdoor torque booster today. I completed the repairs and cycled the system on to verify proper operation of the unit. No other issues were found. The system is working at completion of service.

Installed 2.5 ton Carrier R-454B heat pump system with electric heat kit. Installed Ecobee pro thermostat. Installed new secondary drain pan. Built and installed new supply plenum and return plenum with 20x25 Aprilaire media filter. Rebuilt primary drain, added SS2 / SS3 safety switches. Pressure tested system with nitrogen and pulled vacuum. Sealed all ductwork connections with mastic / hardcast. Cleared primary drain with CO2 and primed trap with water. Weighed in R-454B refrigerant, 62 ambient temp. Tested heating and cooling operation. Everything is working at completion of install.

Performed heater tune-up on a Carrier variable speed heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Cleaned the exterior of the air handler and washed the outdoor coil. All surge protection devices are working. No major issues were found. The system is operational at this time

Heat check completed on a horizontal gas system. Drain line was flushed and treated. Flame sensor was cleaned. All mechanical and electrical components were found within manufacturer specifications. No major issues were found. The system was running at completion of service.