HVAC Service In Buda, TX

Installed new return plenum and made transition to return chase. Replaced return filter cabinet. Rehung ductwork. We removed duct board triangle and went back with home runs. Balanced air in the house. Everything is operational at this time.

On arrival I spoke with the homeowner, and he stated that he wanted to get maintenance done on both systems. He also stated that the main heat pump system was showing a “suction temp sensor fault” at the thermostat. I performed the heater tune-up on two Carrier heat pump systems. Checked the electrical, mechanical and performance systems of the units. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handlers. I secured the compressor wiring and sealed the refrigerant lines at the indoor coil to prevent any attic air from being pulled into the system. I did find that the defrost board and the outdoor suction thermistor are reading the incorrect temperature and causing the system to go into lock out. I spoke with the homeowner and presented options for repairs, and he chose to have the defrost board and sensor replaced at this time. I replaced both components and cycled power at the thermostat. Verified the system is now reading the

Installed a new evaporator coil, with new TXV, for the downstairs air handler. Installed new turbo capacitor to replace a 10/70 mfd capacitor. Installed new two pole contactor. Pressure tested system with nitrogen and pulled vacuum. Rebuilt condensation drain, cleared with CO2 and primed with water. Charged downstairs unit with R-410A. Tested heating and cooling operation

Heating tune-up completed on a vertical furnace. I did find that the air filter was dirty and discussed the importance of changing out air filters more regularly with the landlord and tenant. No other major issues found.

Removed all the refrigerant from the system. Removed the failed TXV and installed a new one. Installed new bi flow filter dryer. Pressure tested line set with nitrogen and used micro leak detector. Rebuilt and insulated primary drain line. Cleared drain and verified operation. Weighed in all new refrigerant as per the communicating thermostat. Also applied some mastic air seal around some of the tape seams I noticed on the supply. Tested in heating and cooling for both operations. Everything is operational at this time.

Performed heater check. Checked electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter is clean. No major issues were found. The system was running at the completion of service.

Built and installed new extended supply plenum. Installed all new flex ducting, buckets and supply registers. Upsized ducting and buckets to 2 bedrooms. Sealed all connections with mastic. Cleaned out return cavity and installed new return grills. Tested heating and cooling operation. Tested static, everything is operational at this time.

Performed the heater tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. The filter was replaced recently and is still in clean condition. Washed the outdoor coil and verified the compressor wiring is secure. I ran the system in cooling mode to check refrigerant levels since the outdoor temperature is 72 degrees. No major issues were found, and the system is operational at this time.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety systems. Tested and verified everything was operating within manufacture specifications for operation. Everything is working at this time.

Performed the heat check on two systems. Checked the electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain line and flow tested them with two gallons of water. I also treated the drain lines. The main house’s filter was replaced with a customer supplied filter. The workshop did not have a spare filter at this time. No major issues were found, and the systems were running at the completion of service.

Heat check completed on a vertical heat pump system. No major issues have been found.

Replaced faulty condenser fan motor. System was cycled to confirm proper operation.

Performed semiannual maintenance on one gas furnace heating system. Tested and verified everything was operating within manufacture specifications for operation. Everything is working at this time.

Performed heater check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The system sterilizers and surge protectors are operational. The air filter was replaced with a customer supplied filter. No major issues were found. The system was running at the completion of service

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a customer supplied filter. The blower wheel has some dust buildup on the wheel. No other major issues were found.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a customer supplied filter. No major issues were found. The system was running at the completion of service.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters were replaced with customer supplied filters. System sterilizers and surge protectors are operational. No major issues were found, and the system was running at the completion of service.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain. The filters have been replaced by the customer this week and are still in clean condition. No major issues were found, and the system was running at the completion of service.

Performed the heater tune-up on a Lennox gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I replaced the high voltage wire nuts with a Wago wire connector. Sealed a hole on the furnace and sealed around the filter with tape to prevent any filter bypass on the system. No other major issues were found, and the system is operational at this time.

Performed the heater tune-up on one American Standard gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I replaced the high voltage wire nuts with a Wago wire connector and sealed around the filter with tape to prevent any filter bypass. No major issues were found, and the system is operational at this time.