HVAC Service In Buda, TX

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety systems. Went over the outdoor condenser fan motor again and checked over how it was running. The amp draw is in the 1.2 range. I let homeowner know the progression of the motor and he will want to replace it this summer. While onsite, I removed the filter grille and washed off all the dust build up on the grille to ensure everything was clean. Tested and verified everything was operating within manufacture specifications for operation. Everything is working at this time.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety systems. Tested and verified everything was operating within manufacture specifications for operation. Everything is working at this time.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters were replaced with customer supplied filters. No major issues were found, and the system was running at the completion of service.

Performed the heater tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Washed the outdoor coil and verified the compressor wiring is secure. I found that the Ecobee thermostat did not have a WiFi connection. I helped homeowner set up the Ecobee and showed her how to use the Ecobee app as well. I also found the compressor minimum outdoor temperature setting was disabled. I set it so that the outdoor unit will not run if it gets below 35 degrees and will instead turn on the heat strips. No other major issues were found, and the system is operational at this time.

Performed the heater tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Washed the outdoor unit and secured the compressor wiring. I adjusted the defrost timer from 90 minutes to 60 minutes to prevent the system from freezing over in heating mode. No other major issues were found, and the system is operational at this time.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. I cleared the condensate line and flow tested the drain with two gallons of water. I also treated the drain line. The system sterilizers are operational. The filter is dirty however the customer did not have a replacement filter at this time. The condenser fan motor showed signs of overheating. No other major issues found.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with water. I also treated the drain line. The surge protection and breathe easy systems are operational. The air filters were replaced with customer supplied filters. No major issues were found. The system was running at the completion of service.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a customer supplied filter. No major issues were found. The system was running at the time of departure.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. The condensation drain line is frozen and I was able to use hot water and get it to drain. The filter was replaced with a customer supplied filter. The air purifier and surge protectors are operational. No other major issues were found. The system was running at the completion of service.

Performed diagnostic and I found that the indoor blower motor has failed which was causing the limit switch to trip shutting down low voltage power to the thermostat. Installed new blower motor inside furnace, secured all wiring and connections, tested furnace and verified operation. Everything is working at this time.

Performed semiannual maintenance on one heat pump heating system. Tested and verified everything was operating within manufacture specifications for operation. Homeowner changed out the Perfect Fit filter prior to us arriving, so the filter is in good and clean condition. Everything is working at this time.

Performed heater check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The Reme-Halo air purifier has failed. The air purifier is receiving power but is not operating. No other major issues were found. The system was running at the completion of service.

Performed semiannual maintenance on one heat pump heating system. Tested and verified everything was operating within manufacture specifications for operation. All Stage 3 Breathe Easy lights are on and operating. Everything is working at this time.

Performed semiannual maintenance on one heat pump heating system. Tested and verified everything was operating within manufacture specifications for operation. Everything is working at this time.

Installed horizontal Carrier gas furnace with propane conversion. Installed a Carrier R-454B condenser and evaporator coil. Rebuilt and insulated primary drain line. Installed SS2 and SS3 safety switches. Installed new return plenum and extended supply plenum. Installed bypass duct and damper. Adjusted gas pressure to manufacturers specification. Pressure tested line set with nitrogen and pulled a vacuum. Added R-454B charge according to line set length. Installed two Ecobee Pro thermostats. Installed one new 16-inch damper and 16-inch flex. Installed new zone control board. Sealed all connections with mastic. Cleared drain with CO2 and tested with water. Tested heating and cooling operation. Also set gas pressures in high and low.

Performed heat checks on two systems. Checked electrical, mechanical, safety, and performance of the system. I cleared both drains and flow tested them with two gallons of water. I also treated the drain lines. The air filters were replaced with customer supplied filters. The surge protection on both systems is operational. No major issues were found, and the systems are running at the completion of service.

Performed a diagnostic on the system and I found that the blower motor has failed. I verified it is receiving proper voltage for operation, but the motor is not responding. I spoke with homeowner, and he chose to have it replaced. I replaced the motor. I then cleaned the interior and the exterior of the air handler. I also washed the blower wheel and housing at no extra charge. I then cycled power at the thermostat and function checked the system. I performed the heater tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Washed the outdoor coil and secured the compressor wiring. I did find the defrost timer was set to 90 minutes and changed it to 60 minutes to prevent the system from freezing over. No other major issues were found, and the system is operational at this time.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air purifier and surge protection are operational. The filter was recently changed and still in clean condition. No major issues were found, and the system is running at the completion of service.

Performed semiannual maintenance on one gas furnace heating system. Inspected all Performance, Mechanical and Safety systems. Tested and verified everything was operating within manufacture specifications for operation. Everything is working at this time.

Installed new extended supply plenum. Replaced all satellite boxes with metal wyes. Ran a dedicated 9” duct to front bedroom with a 12x8x9 bucket and register. Sealed all connections with mastic. Cleared condensation drain line and tested with water. Tested heating and cooling operation.