HVAC Service In Buda, TX

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The wiring is tight and in good condition. The blower wheel is clean, and the blower motor capacitor is within value. The condenser fan motor and contactor are both in good condition. The capacitor for the condenser unit is within value. The condenser unit was drawing normal amperage, and the refrigerant charge is within factory specifications. No other major issues found.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The blower wheel is clean. The wiring is tight and in good condition. The zone control board and both dampers are operational. The condenser fan motor and contactor are both in good condition. The capacitor for the condenser unit is within value. The refrigerant charge is within factory specifications. The condenser coil is clean. No major issues found

Performed semiannual maintenance on one straight cool HVAC system. Inspected all Performance, Mechanical and Safety systems. Cleaned and washed the outdoor condenser. I also taped the filter inside the return air grille to help prevent filter bypass into the unit. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time.

On arrival the homeowner stated that his system had shut off overnight and the thermostat went blank. I performed a diagnostic on the system and found that the low voltage fuse had blown. I used my resettable fuse and cycled the power back on. I cycled power at the thermostat a few times and the system turned on every time without blowing the fuse. I confirmed all electrical connections are tight. I did find a rub out on the high-pressure switch wiring at the condenser. I used foam tape on a few areas of the condenser to prevent other future rub outs. No other major issues were found, and the system is operational at this time.

Performed semiannual maintenance on one straight cool HVAC system. Inspected all Performance, Mechanical and Safety Systems. Cleaned out the outdoor condensing coil to help with better heat transfer of the refrigerant. Flushed and treated the primary drain line that runs outside next to the condensing unit. Everything is working at this time.

Upon arrival the customer stated that the system has not been running for 24 hours. Went upstairs to check the float switch, and found it tripped due to a clogged primary drain line. Presented my findings to the homeowner and he chose to have the drain line cleared. I cleared the drain line and also added some cleaner to help break down excess buildup. I also noticed that the primary drain had come partially loose from the coil so I reattached and secured it. The customer has also opted to join our Gold Maintenance plan. The system is cooling properly at this time.

Homeowner elected to move forward with repairs to the system. Details are below: “Includes replacement of the blower motor capacitor, and outdoor fan motor.” I replaced the outdoor fan motor and tested it. I then went upstairs and replaced the capacitor for the blower motor. I then tested the system. Everything came on and ran properly. System is in working order at completion of appointment.

Homeowner elected to move forward with repairs to the system. Details are below: “Includes replacement of the blower motor capacitor, and outdoor fan motor.” I replaced the outdoor fan motor and tested it. I then went upstairs and replaced the capacitor for the blower motor. I then tested the system. Everything came on and ran properly. System is in working order at completion of appointment.

Homeowner elected to move forward with repairs to the system. Details are below: “Includes replacement of the blower motor capacitor, and outdoor fan motor.” I replaced the outdoor fan motor and tested it. I then went upstairs and replaced the capacitor for the blower motor. I then tested the system. Everything came on and ran properly. System is in working order at completion of appointment.

Homeowner elected to move forward with repairs to the system. Details are below: “Includes replacement of the blower motor capacitor, and outdoor fan motor.” I replaced the outdoor fan motor and tested it. I then went upstairs and replaced the capacitor for the blower motor. I then tested the system. Everything came on and ran properly. System is in working order at completion of appointment.

Performed cooling maintenance on a straight cooling system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I found that the high voltage wire nuts at the furnace were undersized, and the system does not have a water safety switch. I replaced the wire nuts with the correct size to prevent any electrical shorts. No other major issues were found, and the system is operational at this time.

Performed AC cool check. Checked electrical, mechanical, safety and performance of the system. The drain line was cleared and treated. The evaporator coil is rusted but clean. The blower wheel and air handler are both clean. The electrical wiring is tight and in good condition. The blower motor capacitor is below value. The condenser fan motor is showing signs of overheating. The condenser capacitor is below value, and the system is low on refrigerant. I performed a leak check but was unable to find a leak. No other major issues were found.

Performed semiannual maintenance on a 2013 Lennox straight cool system. Inspected all Performance, Mechanical and Safety Systems. Tested and verified all mechanical components were operating within manufacture’s range for operation. Everything is working at this time. Supply temperature of 50.3° upon departure.

Service diagnostic found that the capacitor for the condenser unit has failed. Options for repair were presented to the customer, and he chose to have the capacitor replaced. I replaced the capacitor and cooled the compressor with water. I then function checked the system and the system is now operational.

Service diagnostic found that the capacitor for the condenser unit has failed. Options for repair were presented to the customer, and he chose to have the capacitor replaced. I replaced the capacitor and cooled the compressor with water. I then function checked the system and the system is now operational.

Cool check completed on a horizontal gas system. The drain line was cleared and treated. Found discoloration on the condenser fan motor showing possible overheating. No other major issues found.

Installed new case coil in attic. Removed refrigerant from system, and also removed filter drier from outside. Installed new filter dryer inside near the evaporator coil. Rebuilt drain line and cleared lines with CO2. Installed new condenser fan motor outside and re-insulated suction line. Weighed in refrigerant per factory specs. Everything is working at this time.

I spoke with Mr. Winters, and he stated that he noticed the outdoor fan motor was barely spinning and was extremely hot to the touch the other day. I tested the system and was able to audibly hear the outdoor condenser fan motor failing. I checked the fan blade rotation when the motor was off and noticed that the fan blade could not make a full rotation by itself. I installed a new outdoor fan motor and programmed it to match the speed and rotation of the original motor. I also noticed some oil residue near the suction line service ports, and upon further investigation, I found that the Schrader core salve was not tightened securely. I tightened it down and then added in 2 lbs of R-410A refrigerant which returned the unit back to an 8°SC value, matching the data tag on the unit. Tested and verified all mechanical components were operating within manufacture’s specifications for operation. Everything is working at this time.

I arrived at the home to find the systems off and not running. I spoke to the homeowner about how the units had been performing. I made sure to rinse out both condensers and also clear both drains. The upstairs system is in great shape. No major issues were discovered. The downstairs system has a few problems that I discovered: the float switch has failed, the blower wheel is dirty, the condenser fan motor is leaking oil, and the start kit has failed. I brought all of this to the attention of the homeowner and made them a few options. Systems are working to the best of their ability at this time.

I arrived at the home to find the systems off and not running. I spoke to the homeowner about how the units had been performing. I made sure to rinse out both condensers and also clear both drains. The upstairs system is in great shape. No major issues were discovered. The downstairs system has a few problems that I discovered: the float switch has failed, the blower wheel is dirty, the condenser fan motor is leaking oil, and the start kit has failed. I brought all of this to the attention of the homeowner and made them a few options. Systems are working to the best of their ability at this time.