HVAC Service In Buda, TX

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation. Did change one homeowner supplied 4” filter and verified the Surge Protection and the Stage 3 Breathe Easy System were operating as designed. I did notice large amounts of dryer lint gathering in the attic. Upon further inspection I noticed that the dryer roof vent was not the proper one and was covered by chicken wire. The homeowner said they will contact a roofer to see about getting the correct vent installed.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. Did find that the underside of the indoor fan coil and blower wheel have a buildup of dirt. Also noted that the outdoor condenser fan motor is nearing the rated electrical rating. No other major issues found.

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I found that the electric heat kit is extremely rusted. No other major issues found. See attached checklist for full tune-up details. I presented repair options, and the customer chose to have the heat kit replaced today. I replaced the heat kit and cycled power. Confirmed all heat strips are on and working.

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain and washed the outdoor condenser. Filter was replaced last month. No major issues were found. System is on at this time.

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Customer provided filter for replacement. I found that the outdoor condenser fan motor was leaking lubricant. No other major issues found. I presented my findings to the homeowner and provided options for repair. He chose to have the motor replaced at this time. I replaced the motor and cycled power. System is on and working at this time.

Removed return plenum and supply transition. Installed new return with existing media filter. Added turning vanes and reattached ductwork. Installed square to round with adapter and insulated metal pipe. Relocated four ducts for increased airflow. Sealed pressure points with air lock. Also adjusted the flue away from the attic bracing.

Service diagnostic found that the blower motor has failed; motor is running at all times. During testing I disconnected the speed taps for the motor and the motor was still running. Installed new blower motor for the master bedroom/living area. Also washed the blower wheel and housing (which had microbial growth that I showed to the homeowner). Replaced 10x10 filter. Cycled power at the thermostat and confirmed motor is turning on and off. System is running at this time.

Performed semiannual maintenance on one electric heating system. Inspected all Performance, Mechanical and Safety Systems. Spoke with the client and she mentioned that the air coming from the farthest side of the home was not as warm as the bedroom side. I did find that there is a 15KW heat kit installed however only 10KW is powered due to only one set of wire being ran from the breaker panel. She said she will contact a licensed electrician to see if it is possible to install another set of wires to power the additional heating elements. No other major issues found. See attached checklist for full tune-up details. Flushed out the drain line to help ensure drain line is not restricted. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. No major issues were found. Reme-Halo is operational. Drain line was cleared and treated. Condenser coil was clean. Electrical disconfirmed in and on. System was running at the time of departure.

Pulled out the indoor system and removed the old plywood base. Replaced the base with a new one. Removed the coil and cleaned it. Also replaced the primary drain pan. Put the system back together and installed the system back into the closet. Rebuilt the condensate drain. Re-piped the gas line and added a sediment trap. Added an in-line filter dryer. Sealed the supply plenum back to the system. Checked the operation of the system and cleared the drain. The system is working properly at this time.

Performed heating maintenance on one furnace system. Checked all electrical, mechanical and performance of the system. Customer supplied filters for replacement. Air ionizer is on and working. No major issues were found. System is on at this time.

Installed 5-ton Carrier gas system. Ran new 18/10 wire to the thermostat and installed Ecobee Pro. Installed new extended plenum and return air plenums and sealed with mastic air lock. Installed 20x30 return air filter grille in piano room. Replaced secondary drain pan. Rebuilt and insulated condensate drain line and installed SS2 and SS3 safety float switches. Pressure tested line set with nitrogen and pulled a vacuum on the line set. Replaced disconnect and whip at the outdoor system. Reinsulated the suction line and ran low voltage in 1/2” Seal-Tite. Verified system operation and charged system to manufacturers specifications. Everything is operational at this time.

Performed diagnostic and found a failed outdoor capacitor. Spoke with homeowner and they chose to have it replaced today. After the repair was completed, I verified system operation. Everything is working at this time.

Performed heating maintenance on one gas furnace system. Checked all electrical, mechanical and performance of the system. Replaced 4-inch media filter. No other major issues were found. Customer asked me to set the thermostat to auto. I set thermostat to auto at customers desired temperatures. System is on at this time.

Performed heating maintenance on a heat pump system. Checked all electrical, mechanical and performance of the system. No major issues were found. System is on and running at this time.

Performed heating maintenance on two gas systems. Checked all electrical, mechanical and performance of the systems. I found the ignitor for the downstairs system showing signs of wear and tear. No other major issues were found. I presented my findings to the homeowner, and they chose to have the ignitor replaced with an OEM ignitor. I replaced the ignitor, cycled the furnace and confirmed ignition of the furnace. Filters were replaced before I arrived. No other issues were found. Both systems are on at this time.

Performed heat check on two systems. Checked electrical, mechanical, safety, and performance of the system. All heat strips are operational. Filter changed with customer supplied filter. No issues were found and system running at time of departure.

Installed 3-ton Payne gas system. Replaced supply plenum with a new extended plenum. Installed new Ecobee thermostat. Replaced gas flex line and valve. Installed new plywood overlay and new combustible air vents. Installed new ducting buckets in recently built extension. Installed SS2 safety float switch. Insulated the return air chase. Replaced all supply grilles. Pressure tested system with nitrogen and pulled a vacuum on the line set. Installed a new pad for the outdoor system. Replaced disconnect and whip at outdoor system. Cleared drain line and verified system operation.

Performed heating maintenance on one gas system. Checked all electrical, mechanical and performance of the system. The outlet gas pressure was slightly low, so I adjusted it to 3.5. No other major issues were found. System is on and working at this time.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved and flame sensor cleaned. Filter is a little dirty and should be replaced soon. No major issues were found and system running at time of departure