HVAC Service In Buda, TX

Performed semiannual maintenance on the AC system. Inspected all Performance, Mechanical and Safety systems. Verified everything was working within manufacture’s specifications for operation.

New return plenum and 12x24x1 filter grate was installed. Second run of 10-inch flex duct was added to the return to increase airflow for the system. Repair was completed. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed semiannual maintenance on one Comfort Cooling System. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time.

Diagnosed a clog in the p-trap of the primary drain. Water was leaking from the pan and primary drain due to the clog. Gave the client options to clear drain line and she chose to move ahead with the repair. Cleared the drain line and treated it with solvent. Then tested drain to confirm that it was functioning. Also removed coil door to inspect drain pan and found build up in there as well. Drained water and treated. System is operational at this time.

Diagnosed that the primary drain had backed up tripping float switch. Gave the client options to repair and he chose to have the drain cleared and treated. Repair complete and system is operational.

Installed new Carrier condensing coil. Removed R-410A refrigerant and replaced line filter dryer. Pressure tested system for extensive leak check and pulled deep vacuum. Weighed in new factory charge and verified system operation.

Performed maintenance on the AC system. I checked all electrical and mechanical components. Also cleaned the condenser, checked pressures, and cleared drains. The pressures on the system were out of normal condition and I gave the customer options to repair. She chose to hold off at this time. System is operational. Disconnect is in and thermostats are set to customer preferences.

Performed service diagnostic. Diagnostic found that the capacitor on the condenser unit had failed. Condenser fan motor also showed signs of overheating. Options for repair were presented to customer and they chose to replace the capacitor and fan motor. Repairs were completed. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. No major issues were found. Drain line cleared and treated. Condenser coil cleaned. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. Some mold/mildew was found inside the air handler. No other major issues were found. Drain line cleared and treated. Condenser coil cleaned. Options for repair were presented to customer and they chose to have our Breath Easy Stage 3 package installed. Repair was completed. Electrical disconnect confirmed in and on. System was running at the time of departure.

Diagnosed a failed capacitor. As we were checking the system, we also discovered that the system is low on refrigerant. Gave the client his options for repairs and he chose to have the capacitor replaced and charge the system. He also joined our maintenance program. Completed repairs. Performed cool check. We cleaned the condenser, cleared the drain and checked all mechanical and electrical systems. System is set to customer preference and the breaker and disconnect are in place.

Installed new high-pressure switch into condenser and performed maintenance on system. Cleaned condenser coil. Checked pressures and cleared drain. System is set to customer preference and disconnect is in place.

Replaced evaporator coil. Rebuilt condensate drain line and insulated it. Installed SS-2 and SS-3 float switches. Sealed coil to furnace and supply. Replaced inline filter dryer, pressure tested with dry nitrogen, and pulled a vacuum on copper line set. Installed attic insulator. Charged system to factory spec. System is working properly at this time.

Performed cool check on two systems. Checked electrical, mechanical, safety, and performance of the systems. No major issues were found. Drain lines cleared and treated. Condenser coils cleaned. Electrical disconnects confirmed in and on. Systems were running at the time of departure.

Performed maintenance on the AC system. During system maintenance, I cleared the drain line and cleaned the condensing coil. Also checked pressures and system is in good condition. Checked capacitor with no issues. System is operational at this time.

Performed service diagnostic. Diagnostic found that the capacitor on the condenser unit had failed. Options for repair were presented to customer and they chose to have the capacitor replaced. Repair was completed. Electrical disconnect confirmed in and on. System was running at the time of departure.

Blower wheel was removed, cleaned, and then reinstalled. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed service diagnostic. Diagnostic found that the condenser fan motor was not running due to a failed fan capacitor. Compressor was in thermal lockout. Options for repair were presented to customer and they chose to have the capacitor replaced and join our maintenance plan. Compressor was cooled and fan capacitor was replaced. Electrical disconnect confirmed in and on. System was running at the time of departure.

On arrival, found the outdoor exhaust removal system had failed causing the refrigerant circulation system to stop running. Presented repair options. Replaced the outdoor voltage enhancement system, along with a new exhaust removal system. Also cleaned the outdoor heat transfer media coil.

Checked system and discovered that the temperature split was a high. We raised the fan speed and checked the charge. Then we charged the system to factory specifications and checked the capacitor which was still within range. System is operational upon departure.